UNSOLVED

glenngray

updated

22 years ago

Closed

G

glenngray

6 Posts

0

14279

March 3rd, 2004 22:00

Help my Inspiron 8100 SXGA+ LCD Screen Dark and/or Flickering.

My Inspiron 8100 SXGA+ LCD screen has become dark and/or flickering.  Preliminary reasearch on the net seems to indicate that the inverter card has gone bad.  Using an external monitor the display is OK, so the video card must be good?  Seems to be no difference with AC power or battery only.  I might also note here that occasionally for a short time (seconds) the screen will fully light which I assume means that the flourscent blub is OK. So I disassembled the top case half and extracted the LCD panel.  It is a Hitachi TX38D99VC1CAA LCD screen.  Looking from the back, the lower left quadrant contains what I presume is the inverter card.  It's markings are 67301900, J12I005.00 and 0120020-3b. My questions are 1. What is the card in the upper right quadrant of the panel and is it a concern too?  2. In the disassembly process I found a small chrome covered (all but one side) magnet.  The size of this critter is about 1/4x3/16x1/8 and was sitting askew (at an angle-dislodged?) on the outer rim of the LCD panel. What is this magnet for, and could it be part of or the problem?  What should I do with it when reinstalling the LCD panel?  It is no longer attached to the panel.  3. Should I replace the inverter (J12I005.00)?  Best price I can find so far is $75.  4. Is the inverter card (J12I005.00) the only inverter card that can be used with this Hitachi LCD panel or can other cards be used?  Sorry to be so lengthy here, but it's the best I can do.  A direct reply to inverter@glenngray.com would be nice too.  Thanks.

  • jk79

    412 Posts

    298

    0

    Posted March 4th, 2004 06:00

    As far as the magnet is concerned, it is most likely used to trigger a hall effect sensor to let the system know when the screen is closed.  Not replacing it exactly where it belongs will keep the system from going into standby when you close the screen.  Does it look like there is slot or groove that it may have fallen out of on the plastic frame anywhere, maybe even a spot of glue (In the 5150 it is located above the screen a little bit left of middle, possibly in the latch mechanism)?  As for the other issues, it does sound as though the inverter is to blame.  Sorry I can't help with part numbers and Identifications.

     

    JK

    Message Edited by jk79 on 03-04-2004 03:14 AM

  • igelws

    1 Message

    298

    0

    Posted March 4th, 2004 10:00

    I have de same problem. Please help. Thank you.

    igelws@hotmail.com

  • schnake

    7 Posts

    298

    0

    Posted January 28th, 2005 09:00

    I have the same LCD on my Inspiron 8000, and similar problems to yours (on for a while, some flickering, but after 1-10 secs of operation backlight turns off).
     
    I'm not sure whether to replace the Inverter board or the CCFL.
     
    Did replacing the Inverter work for you?
  • schnake

    7 Posts

    298

    0

    Posted January 28th, 2005 09:00

    How 'bout you igelws, did you manage to solve your problem? And if yes, was it the Inverter board or the CCFL?

  • glenngray

    6 Posts

    298

    0

    Posted January 28th, 2005 09:00

    I was able to obtain a used inverter which when installed did not solve the problem. Inverters are brand specific for each display. Unfortunately it was impossible at the time to obtain a new inverter. I had offers for repair but it required me to send in the display which I was not willing to do. I purchased a new display. Complete unit, case and all,from the hinges up, Turned out for me this was the most sensible answer to the problem. Wish I could be of more help, but that's my story.
  • schnake

    7 Posts

    298

    0

    Posted January 28th, 2005 13:00

    Well thanks for the closure. There were a bunch of other postings in this forum about people installing inverters, but never to be heard from again. It was like some sort of secret Inverter society conspiracy or something.
     
    Now after you installed this used (but different) inverter, were you still getting the same problems?
     
    I'm trying to rule out the inverter as a cause of the problem. But there's still the CCFL backlight or the flex-cable that could be at fault.
  • schnake

    7 Posts

    298

    0

    Posted January 31st, 2005 01:00

    ok, what an adventure I had the last couple of days. Upon someone's advice, I tried to get a volt reading on the ribbon cable that goes into the inverter. Instead, I (idiotically) must have cross-connected some wires causing my machine to shutdown and not startup. I thought that was it. A $5000 investment (circa 2001) now just a pile of scrap metal.

    Well I had nothing to lose, so I went about fully disassembling my notebook. Somewhere along the way, I thought, perhaps the adapter was the problem, and sure enough the power adapter's LED was dim. So unplugged power adapter, and plugged in battery, and sure enough my notebook is working again! This ofcourse I discover after I had stripped the system down to just the core (processor and motherboard).

    So here I thought I lost my adapter, and those things cost a pretty penny too! But at some point I ventured upon the idea of trying to fix the adapter. Unplugged it from the wall socket. But just for the heck of it, tried to see if maybe the adapter would magically work if I plugged it back in. Lo and behold the LED lights up, my adapter is working again, and even works once connected to my notebook.

    Kudos to the people who design these components for putting in all these protective measures! So for anyone who thinks they lost their computer or adapter, try unplugging and replugging it into the power outlet, and that may solve your problem.

    But my initial problem still remains -- my display's down -- either a CCFL or an Inverter problem. I'm guessing it's the inverter, at least the voltmeter seems to reflect a complete drop in voltage after the initial "arcing" period.
     
  • glenngray

    6 Posts

    298

    0

    Posted January 31st, 2005 02:00

    schnake, I guess I did not make it totally clear. I did try the used inverter and IT WAS THE CORRECT INVERTER. Alas it did not correct the problem so as I said before I purchased a replacement display. I still have the old display and hope that someday I can find a new inverter.