UNSOLVED

kal800

updated

20 years ago

Closed

K

kal800

8 Posts

0

13298

May 8th, 2007 17:00

External monitor video modes for D420 - PROBLEM UNSOLVED - UNBELIAVABLE!!!

Dear Forum Members, especially those from Dell Company, For half a year I've been experiencing problem described above: External monitor (CRT in my case) connected to Latitude D420 is unable to work in higher modes than 1024/768@60Hz. I have seen so many posts related to that bug since that time. AFAIK it occurs also on D620 model. Also I have seen responses from Dell technicians, but very typical - reinstall drivers, ensure that BIOS version is the latest, etc... I have been downloading new drivers as they were appearing on the Dell webpage - obviously effortless. I am not able to perform any job requiring bigger screen till now. I really cannot believe that such company as Dell is not able to fix such a bug - for me this is very serious even I would say critical problem. WHAT IS HAPPENING??? Kal
  • rc55

    2 Posts

    342

    0

    Posted May 9th, 2007 20:00

    Well, I can try and help. Most of the time on changing of resolutions sometimes the output frequency is too much for the monitor to handle and the screen goes blank.

    I'd say try using RefreshForce:
    http://www.pagehosting.co.uk/rf/

    ...and force the higher resolutions at a lower refresh rate, try 60Hz intially and experiment around these.

    Ruairi
  • 342

    0

    Posted May 13th, 2007 14:00

    Hi there!
     
    This is probably the same problem that is present in the drivers for all integrated Intel graphics chips (such as GMA950).
     
    It seems that if you connect an external monitor which does *not* communicate with the Laptop to tell it which modes it supports (so-called EDID data), the Intel driver does not offer anything else than 800x600 and 1024x768.
     
    This is a stupid strategy with serious drawbacks: I personally would like to connect my Inspiron 640m with my flatscreen TV. The TV supports a resolution of 1360x768, but whatever I do, I cannot configure the laptop to more than 1024x768, just as you describe here. Many people trying to connect laptops with Intel graphics chips to beamers and other devices that don't transmit EDID data have the same problem. See here for a discussion on these issues and ideas for possible solutions (none of which works so far as I can see):
     
     
    Now the problem is mainly caused by the Intel drivers, but some of it also comes from restrictive Bios settings. I think if Dell cared they could modify the system Bios and then at least custom resolutions could be activated with tricks (like modifying the INF file of the Intel graphics drivers before installing them).
     
    More info is here on the Intel page:
     
     
    There it says that "custom display modes [...] are defined within the Video BIOS Table (VBT)", and this is where Dell could program in more modes.
     
    Anyway, this is really a serious issue keeping many people from using their laptops as they would like to. And all this just because of stupidly programmed graphics drivers ... :(
     
    Cheers,
    Tim


    Message Edited by SirPercivale on 05-13-2007 10:53 AM
  • john-z

    1 Message

    342

    0

    Posted May 16th, 2007 02:00

    Tim,
     
    You've got the problem pegged and it is extremely annoying.  I got all the standard "try new drivers" and "your monitor isn't supported" answers from Dell.  What irks me the most is that there IS a solution but no one at Dell cares enough to figure the problem out.  I bought an Inspiron 6400 (with Vista and the Intel 945GM graphics card) that I wanted to connect to a 24" Dell P1690 Trinitron CRT.  I tried every possible permutation and combination of changing settings, connecting a new display, changing settings in Windows and changing settings in the Intel GMA app.  Dell told me it was a Vista problem, because Vista was only showing Generic monitor drivers.  Turns out Vista does include drivers for my monitor, though Dell didn't help me to find that out (Dell doesn't have a Vista compatible driver available for download on their website).
     
    Dell misled me into thinking that switching back to XP would solve the problem.  When I found this thread, I realized this problem existed in XP and isn't a Vista issue so I abandoned a system wipe and OS downgrade.  However, after literally spending nearly 12 hours trying to figure out a solution, I accidentally did something and all of the sudden I had 1920X1200 resolution on my CRT and at a beautiful 76 Hz.  Only problem was I didn't know how I got it, but I didn't care.... at least until I had to reboot and it no longer worked.  It took me another 3 hours to figure the problem out, and now I can get it to work fine, anytime!!!
     
    I am not a system hardware or driver guru, but I believe the problem lies in the Intel software which is intercepting or obstructing Windows PnP operation.  I believe the Intel software is not permitting proper EDID communication, because my monitor supports EDID.
     
    All I want is a guarantee that Dell will add a Knowledge Base article on the problem with solution and that they will work with Intel to fix the problem.  If you want to know the solution, just reply with an email address and I'll send it offline until Dell commits to solve the problem.  BTW, it requires no changes to configuration or any settings!!
  • kal800

    8 Posts

    342

    0

    Posted May 23rd, 2007 10:00

    kal800@gmail.com
  • chrisrolke

    13 Posts

    342

    0

    Posted May 24th, 2007 18:00

    thanks

    Message Edited by chrisrolke on 05-29-2007 07:49 AM


    Message Edited by chrisrolke on 05-29-2007 07:49 AM
  • 342

    0

    Posted May 27th, 2007 04:00

    have you tried deselecting "hide modes this monitor cannot display?"