UNSOLVED

Tiger9801

updated

19 years ago

T

Tiger9801

11 Posts

0

20725

January 25th, 2008 22:00

XPS 420 Memory Speeds

Hello,
 
I purchased my XPS 420 at the end of November and going through some testing just found some problems with my motherboard/PSU or something?!?!
 
I purchased it with 2GB of DDR2 6400 (800Mhz) Ram.  I have since added more Ram to get up to 4GB and I made sure that the new ram was 800Mhz also. But now when Iook in different things like the Dell Auto System Scan, Norton System Properties and CPUZ-ID,  I am finding that my system Ram is actually running at only 400Mhz at 1.8v.
 
This should actually be reading out at 800Mhz shouldnt it?
 
I had problems with my 8800GT Video Card and Dell replaced it with a 8800GTX, BUT I have the 425W power supply, which is what Dell Recommends, so I shouldnt be short on power causing a slow down..
 
Can Someone Please give me some information on this?!? here is a partial cut of my CPUZ-ID Report:
 
Thank you VERY MUCH!!!
 
 

CPU-Z 1.43 report file

Processor(s)   Number of processors 1
Number of cores 4 per processor
Number of threads 4 per processor
Name Intel Core 2 Quad Q6600
Code Name Kentsfield
Specification Intel(R) Core(TM)2 Quad CPU Q6600 @ 2.40GHz
Package Socket 775 LGA Family/Model/Stepping 6.F.B Extended Family/Model 6.F
Core Stepping G0 Technology 65 nm
 
Core Speed 1596.0 MHz Multiplier x Bus speed 6.0 x 266.0 MHz
Rated Bus speed 1064.0 MHz
S tock frequency 2400 MHz
Instruction sets MMX, SSE, SSE2, SSE3, SSSE3, EM64T
L1 Data cache (per processor) 4 x 32 KBytes, 8-way set associative, 64-byte line size
L1 Instruction cache (per processor) 4 x 32 KBytes, 8-way set associative, 64-byte line size
L2 cache (per processor) 2 x 4096 KBytes, 16-way set associative, 64-byte line size
Chipset & Memory   Northbridge Intel X38 rev. 00
Southbridge Intel 82801IR (ICH9R) rev. 02
Graphic Interface PCI-Express PCI-E Link Width x16 PCI-E Max Link Width x16
 
Memory Type DDR2
Memory Size 4096 MBytes
Memory Frequency 399.0 MHz (2:3)
CAS# Latency (tCL) 5.0 clocks
RAS# to CAS# (tRCD) 5 clocks
RAS# Precharge (tRP) 5 clocks
Cycle Time (tRAS) 15 clocks
Command Rate (CR) 2T
 
System  
System Manufacturer Dell Inc. System Name Dell XPS420
Mainboard Vendor Dell Inc. Mainboard Model 0TP406
BIOS Vendor Dell Inc. BIOS Version A03 BIOS Date 01/02/2008
 
Memory SPD 
Module 1 DDR2, PC2-6400 (400 MHz), 1024 MBytes
Module 2 DDR2, PC2-6400 (400 MHz), 1024 MBytes
Module 3 DDR2, PC2-6400 (400 MHz), 1024 MBytes
Module 4 DDR2, PC2-6400 (400 MHz), 1024 MBytes
 
Software  
Windows Version Microsoft Windows Vista (6.0) Home Premium Edition (Build 6000) DirectX Version 10.0
  • xrogly

    10 Posts

    969

    0

    Posted January 25th, 2008 22:00

    I'm not really sure... have u checked your BIOS? Also I don't know if this would affect the frequency but did you check your pagefile?
  • Davet50

    6 Operator

    •

    14442 Posts

    969

    0

    Posted January 25th, 2008 23:00

    in your memory freq listing how much is 2 X 399?  this is the way it its reported...mine shows the same thing....
     
    I tried to find the response that Cadametz wrote that explains the whole thing maybe he will jump in ...


    Message Edited by Davet50 on 01-25-2008 08:38 PM
  • Tiger9801

    11 Posts

    969

    0

    Posted January 26th, 2008 00:00

    My page file is only set to about 1.5 the total of my physical Ram. I have set it for about 4.5 or something like that due to the fact that windows only reads the 3.25 in 32 bit.
     
    I am not sure what you are getting at about the 2x399Mhz to equal the 800Mhz..
     
    Here is basically what I am looking at:
    Memory SPD 
    Module 1 DDR2, PC2-6400 (400 MHz), 1024 MBytes
    Module 2 DDR2, PC2-6400 (400 MHz), 1024 MBytes
    Module 3 DDR2, PC2-6400 (400 MHz), 1024 MBytes
    Module 4 DDR2, PC2-6400 (400 MHz), 1024 MBytes
     
    I would think it would look more like:
    Module 1 DDR2, PC2-6400 (800Mhz), 1024MBytes
    and so on.
  • exponential

    43 Posts

    969

    0

    Posted January 26th, 2008 01:00

    Just let windows manage your page file size. 400MHz is the correct reading. It is DDR so 2 transactions take place per 1 cycle. That is where 400 x 2 = 800 MHz. That is ballpark, so it can be off by a MHz or two.
  • Tiger9801

    11 Posts

    969

    0

    Posted January 26th, 2008 02:00

    Ok... Thank you very much for the information!!
  • eskymi

    1061 Posts

    969

    0

    Posted February 1st, 2008 20:00

    I know this thread is a week old, but I tried CPU-Z and just wanted to find clarification.

    I have 667mhz, so the reading of 333.3 is correct....right?  As 333.5 one way and 333.5 the other equals 667...

    Cool....but I do have one question why does core speed show 1.596 if it's a 2.4, or are they two different numbers?  I have not used the program before and would like to learn more.

     

    I'll do a search for Cadmetz also and see what his original explanation was...

    Message Edited by eskymi on 02-01-2008 05:42 PM
  • Davet50

    6 Operator

    •

    14442 Posts

    969

    0

    Posted February 1st, 2008 21:00

    if you are at idle the processsor could be throttled down. not sure if you have speedstep in your bios will have to look but that could be the main reason...remember to multiply the bus speed reading times four as you have four cores...

    as for the memory speed look at the memory tab at  the FSB:DRAM ratio..

  • eskymi

    1061 Posts

    969

    0

    Posted February 2nd, 2008 11:00

    Thanks Davet50

    I have been using more new programs since I started perusing these forums and I am glad I can ask questions to help me learn what I am looking at.

    I have an Inspiron E1705 and downloaded the fan program (I8kguifan) or whatever it is called.  And with help on these forums, I have learned how to use the program, what the numbers mean...and it's been very helpful.

    Now I have another tool I can use and at least understand what I am looking at.

    JOE>>>>(eskymi)