MEC2

updated

16 years ago

M

MEC2

7 Posts

0

114155

March 25th, 2011 13:00

Vostro 230 and E2210 via DVI screen will not wakeup

Hello -

Have many new identical Vostro 230 systems with E2210 hooked up using DVI. They all are showing an odd problem - when the screen goes to sleep for power savings (the screen, not the PC, sleep is disabled), they intermittently will NOT wake up. Systems are on but no video. Only way to get video back is hard reset. Multiple machines, same problem. As a test, used VGA, and no problem waking up (so far).

Something obviously is amiss, I suspect with the onboard video when using DVI. Anyone have any information? Needless to say, we won't be getting more of these until we have a resolution...

Thanks...

  • 2475

    1

    Posted May 11th, 2011 11:00

    Braytonak,

    You can cancel your installation with your new materials because a Senior Technical Analyst on Dell support have researched the issue we are having on the Vostro 230 trying to run dual monitors with the onboard vga jack and the add in DVI jack.

    This is a non supported configuration.  The DVI add-in card is a pass-through and not an actual graphics card.

    The issue has previously been brought to INTEL as the issue is with the INTEL Driver. Intel has said they will not be correcting the issue in any future driver releases.

     

     Currently there are a number of workarounds available:


    Use VGA only


    also downgrade to the 8.15.10.1749 or 8.15.10.1872 Intel driver, just search on google  ==> This is working fine for me on Windows 7 x64

    For Windows XP this one also seems working fine ==> 6.14.10.5090

     

    Alternatively, installing an add-in graphics card will also resolve. (ex. Diamong ATI Radeon HD3450 PCI-E 512mg low profile)

  • DELL-Chris M

    Community Manager

    •

    56891 Posts

    •

    232143 Points

    2470

    0

    Posted March 25th, 2011 21:00

    MEC2,

    You mention onboard video. Is that port VGA? If yes, are you using a VGA to DVI adaptor and to the monitor DVI cord?


    DELL-Chris M (old account)

    #IWork4Dell

  • MEC2

    7 Posts

    2470

    0

    Posted March 28th, 2011 10:00

    Yes, the units shipped with the DVI port. We are using DVI to DVI on the monitor, no funky adapter or anything.

    My guess is driver/BIOS on the video card and something in Windows 7 on the monitor powersave. But certainly, this shouldn't happen...

    Problem seems resolved if you use the VGA to VGA to the same monitors...

  • JorgeLaf

    2 Posts

    2470

    0

    Posted April 7th, 2011 15:00

    I am having the exact same problem with two brand new Vostro 230's.  PCIE DVI Card added from Dell to give digital video out rather than analog.  Have updated drivers, tried to flash the bios (no new bios), reinstalled Windows 7 Pro.  All to no avail.  Next step for me is to call Dell ProSupport.

  • braytonak

    17 Posts

    2470

    0

    Posted April 19th, 2011 16:00

    This sounds precisely like the problem I'm experiencing.  Vostro 230s with the add-in PCI-E card that contains a single DVI connection.  I'm using two Dell E198WFP flat panel monitors.  These can accept both DVI and VGA.  Unfortunately, the second video card cannot output the analog (VGA) signal through its DVI-D connector.  If it could, I wouldn't be writing this.

     

    At first, the system ran fine.  Then I noticed, like you, that the screens wouldn't turn on after the system put them to sleep.  I found that I could wake the screens if they had only been off for a few minutes, but that I would hear the "Device Connected, "Device Disconnected" sounds over and over until they awoke.  Every morning the screens would be blank and  I would have to do a hard-reset of the computer to get them to turn on.

     

    This has progressively become worse.  Now it is to the point that only the VGA-connected display will function.  The moment I turn on the DVI-connected distplay, the device-connection tones start happening, the monitor goes right to sleep, Device Manager goes nuts with refreshing the device list, the Screen Resolution control panel starts blinking with every detect and disconnect of the monitor and the monitor never shows an image.

     

    If I restart the computer, both monitors are fine until Windows 7 Enterprise (32-bit) gets to the login screen.  At that point the DVI-connected monitor turns off.  Upon login, the sounds from the speakers starts, as if I'm turning the monitor on and off.

     

    I've checked the BIOS, updated the drivers (via Device Manager) for the monitors, I've looked for BIOS and driver updates on the Dell website, re-seated the add-in card, swapped monitors, swapped cables, swapped primary monitor settings in the Control Panel, turned off the monitor sleep settings in the Power Options control panel and was just today able to find a much newer video card driver from Intel than what Dell supplies.  (Integrated graphics.)  None of this has made any improvement.  The only thing that helps is to leave the DVI-connected monitor off. 

     

    This secondary card is sounding like a serious waste of money.  Any other trouble-shooting hints?

  • 2470

    0

    Posted April 20th, 2011 14:00

    Hi,

    I have exactly the same big issue on many Vostro230 desktop (~15)

    XP Pro or 7 Pro - VGA or DVI as primary with or without converter - muliple brand of monitor..etc.

    Bios, Windows and Driver are fully updated or outdated :)   All configuration has been tested (resolution, sleep On/off, power config....etc) and nothing has changed.

    So whatever is my setup on my PC I always have this problem  with the your PCIE 1x card with DVI connector (KH276, ref: 320-5252)

    Note: When I put other video card like ATI or NVIDIA to dedicate my monitors all working fine!

    Dell GOD! Please help!

  • wripley

    1 Message

    2470

    0

    Posted April 25th, 2011 11:00

    I disabled the sleep & energy-saving features and it works for a while - but defeats the whole point of trying to save energy.  Still need to simply press and hold the power button until the pc dies.  Upon restart, I get the boot screen asking if I want to run in safe mode - as if I got the blue screen of death when the DVI monitor was inoperable.  If I could have bought Win XP with this Dell I would have but they offered only the newest (translation: most unstable) OS.  What a pity.  Maybe the solution is to revert back to XP?  Or switch to an HP machine instead.  XP on my Mac runs better than Win7!  I've held off on buying two additional machines until (if) Dell's hardware and Microsoft's software can speak the same language.  I would like to know how this can be fixed - or at least patched.

  • JorgeLaf

    2 Posts

    2475

    0

    Posted April 25th, 2011 14:00

    I am having the same problems.  I posted earlier looking for help.  I ended up calling Dell Pro Support.  We ended up pulling the DVI pciE card out of one of the computers I was having this problem with.  Once that was done, all problems stopped with that computer.  The one we left the card in has continued to have to be hard booted every morning.  I will be calling back to ProSupport in a little while.  There has to be a solution to repair this problem.  It lookes like the card is totally bogus!  So, if you have having this problem, Pull the DVI Card and Call Dell to get them to replace it with something different!

  • braytonak

    17 Posts

    2475

    0

    Posted May 11th, 2011 10:00

    I did a Dell Chat session yesterday.  The technician is sending a motherboard, hard drive and secondary video card.  I doubt that it will have any impact on the situation.  I'll reply back after I've done some testing.  The technician had no response to my question about returning the card.  I guess the solution will be somewhere at the other end of a flow chart that I'm now in.

  • braytonak

    17 Posts

    649

    0

    Posted May 11th, 2011 15:00

    Thanks for the additional info.  As I use Windows 7 32 bit, I have downloaded the appropriate version of the downgraded driver.  Although it appears to be intended for mobile applications and it has the Gamma maxed out by default on the secondary display, I finally have what seems like a functional system for the first time in weeks.  As you know it will take me some time to be sure that the system still doesn't crash after being left alone overnight.  Hopefully this is the permanent 'fix' that I've been looking for.  I'll post back with any experiences over time.

     

    The Windows 7 32 bit driver that I downloaded was from http://www-307.ibm.com/pc/support/site.wss/document.do?lndocid=MIGR-74300