UNSOLVED

lartb

updated

22 years ago

L

lartb

5 Posts

0

8794

October 22nd, 2004 19:00

Sysprep'd image to a GX280

Our reference system is a GX260 and when adding support for new hardware we have been simply  adding the new drivers and entries to the Sysprep.inf file (see below).  This has worked fine in the past, but a GX280 won't boot into mini-setup.  It tries to boot, fails, brings up the safe mode boot menu and repeats.
 
The other weird thing is that when I try to build the mass storage driver section on a 280 (with the drivers loaded) I don't see any devices with a HWID matching the IDE controller in the sysprep.inf...
 
Any help would be greatly appreciated!
 
----- (Relevent Sysprep.inf sections) -----
 
[Unattended]
  DriverSigningPolicy=Ignore
  UpdateInstalledDrivers=Yes
  OEMPnPDriversPath=source\drv\GX280;source\drv\GX270;source\drv\GX260;source\drv\d600;source\drv\C840;source\drv\GX150
[SysprepMassStorage]
PCI\VEN_8086&DEV_2651 = C:\SOURCE\DRV\GX280\ich6ide.inf
PCI\VEN_8086&DEV_2652 = C:\SOURCE\DRV\GX280\ich6ide.inf
PCI\VEN_8086&DEV_266F = C:\SOURCE\DRV\GX280\ich6ide.inf
PCI\VEN_8086&DEV_24DB = C:\SOURCE\DRV\GX270\ich5ide.inf
PCI\VEN_8086&DEV_24CB = C:\SOURCE\DRV\GX260\ich4ide.inf
PCI\VEN_8086&DEV_24CA = C:\SOURCE\DRV\D600\ich4ide.inf
PCI\VEN_8086&DEV_248A = C:\SOURCE\DRV\C840\ich3idem.inf
  • DaveyB0_2

    1 Message

    135

    0

    Posted October 26th, 2004 09:00

    Have you set the SATA controller to 'Combination' mode in the BIOS
  • lartb

    5 Posts

    135

    0

    Posted October 26th, 2004 13:00

    Yeah, I tried that and had the same problem.  It's like sysprep isn't adding the mass storage driver the way it's should be!
  • lartb

    5 Posts

    135

    0

    Posted October 26th, 2004 18:00

    I added in a sysprep.inf entry for a generic IDE controller, and now the mini-setup starts but locks up in the middle.  It simply says "Please wait...", and never continues.  I believe this is the point where device detection occurs, but I'm not sure.
     
    ---- For posterity, here is what I added to my previous sysprep.inf [SysprepMassStorage] section
     
    ; Generic IDE Controller
    ; Should only be used if there are problems loading the manufacturer drivers!
    ; Verify that the appropriate IDE drivers are being loaded by the system, not
    ; these generic drivers as performance may not be optimal.
    *pnp0600 = c:\windows\inf\mshdc.inf
    pci\cc_0101 = c:\windows\inf\mshdc.inf
    primary_ide_channel = c:\windows\inf\mshdc.inf
    secondary_ide_channel = c:\windows\inf\mshdc.inf
  • djgarcia

    223 Posts

    135

    0

    Posted October 26th, 2004 18:00

    try adding the DSS to your image. 

    <ADMIN NOTE: Broken link has been removed from this post by Dell>