UNSOLVED

toast-

updated

19 years ago

T

toast-

19 Posts

0

15153

December 2nd, 2007 16:00

Replaced motherboard on XPS 700, will not boot

I received a new XPS 720 motherboard about a month ago through the exchange program. I was contacted by a technician, but after calling him back three or four times, he never came over. Eventually i just gave up and switched it out myself. I made sure i went through the proper procedure, and all of the cables are hooked up, and all of the expansion cards are back in the proper place. The power cables are attached to the motherboard, although i have to admit that i'm unsure if the hard drives are plugged in right. There's an area of 6 spots where there are connectors that fit into the cable that goes to my two hard drives, one is blue, and the other five are black. I don't remember either of them being hooked into the blue one, so i kept it that way. Well, the system won't start when i power it on. There's a brief moment of about two seconds where the fans run, but nothing on the screen and no lights in front, and then it just shuts off. It seems like something must be disconnected, but i've double checked that it's all in. And yes, i moved the processor and ram over. Any possible explanation? I can even get pictures if needed.
  • gdwrnch3

    2 Intern

    •

    3278 Posts

    445

    0

    Posted December 2nd, 2007 18:00

            Was your systems hard drives configured in a raid array?
    The blue port is usually sata0, and generally your first drive is plugged into that.
      The first time you powered on, did it go through the manufacturers setup on your monitor?  Like this:
     
     
    Power on and tap the key to see if you can get into the bios. If you can, see if your hard drives are recognised by the bios
     
     
  • toast-

    19 Posts

    445

    0

    Posted December 2nd, 2007 20:00

    I fixed it, and eventually got to that screen :D i realized i had to change out a few cables with the new board. Now that it's up and working fine, I found another problem that could potentially be serious. I don't have a system or CPU temperature in nTune, and my RPM's are off. System RPM reads 31k RPM, nForce reads 700 RPM, and "Aux2" reads 38RPM. Obviously, the system RPM is way off - it's usually around 1000 stable. Even more worrying, i don't have a reading for CPU temperature, only my GPU. I applied a half-assed coat of thermal grease on the processor when i switched it over to the new board, but i made sure it was mostly covered. I'd like to know what temperature i'm at, and with this 680i chipset i'll be wanting to do some overclocking....Any reason why my CPU temperature isn't registering? I went to the nvidia site and installed the 680i drivers thinking i needed them. Could this have affected it?
  • Davet50

    6 Operator

    •

    14442 Posts

    445

    0

    Posted December 2nd, 2007 21:00

    try picking up a copy of Core temp form here
     
    Did you reinstall ntune???
    Did you enable the performance section in the Bios...
     
     
  • toast-

    19 Posts

    445

    0

    Posted December 3rd, 2007 01:00

    Aha! The problem has been solved. nTune now shows an idle CPU temperature of 38C. A little bit high. Does anybody know if i can use aftermarket heatsinks and CPU fans on the XPS 720 board?
  • Davet50

    6 Operator

    •

    14442 Posts

    445

    0

    Posted December 3rd, 2007 13:00

    what processor are you running. Did you clean off the old thermal past from the processor and the heat sink then reapply NEW paste?
    The supplied heat sink has been more than adaquate for almost all processors...you can get the  Dell cooler but it runs around 500...
  • toast-

    19 Posts

    445

    0

    Posted December 9th, 2007 18:00

    Yeah i reapplied a new coat of thermal paste after cleaning the old stuff off. Although, i did break the seal again when i accidentally flipped the heat sink up. Is that ok? Are you saying that the dell heatsink is better than any aftermarket options?
  • Davet50

    6 Operator

    •

    14442 Posts

    445

    0

    Posted December 9th, 2007 19:00

    i think is should be ok as long as you didnt fire up the beast and heat it up...
    Im not saying that the Dell heat sink is better just up to the task...
    I believe that there was one user who has a liquid cooler. The problem lies in the Dell connectors and aftermarket fans/coolers...you will proably get errors on the boot up..
  • toast-

    19 Posts

    445

    0

    Posted December 9th, 2007 19:00

    Oh and i'm using the core 2 duo E6300.
  • toast-

    19 Posts

    445

    0

    Posted December 10th, 2007 23:00

    You could be right. I forget what designation the XPS motherboard has, but i know its not a standard board. The connectors COULD be different, but it's my guess that any cooler or heatsink would have a standard power dongle.