UNSOLVED

gbensonsr1

updated

19 years ago

G

gbensonsr1

114 Posts

0

20868

September 14th, 2007 16:00

new bios

dose anyone know if the new bios update DME521-010111 is safe to use?
 
 
 
 
 
 
 
 
Dell Dimension E521
Processor : AMD Athlon 64 X2 3800+ @ 2000 MHz
Physical Memory : 2048 MB (4 x 512 DDR2-SDRAM )
Video Card : Nvidia Corp GeForce 6150 LE
Hard Disk : ST3160812AS (160 GB)
Hard Disk : WDC (250 GB)
DVD-Rom Drive : TSSTcorp CDRWDVD TS-H493A
Monitor Type : Dell Computer DELL E207WFP LCD 20' MONITOR
Operating System : Microsoft Windows XP Professional 5.01.2600 Service Pack 2
DirectX : Version 9.0c
  • mombodog

    2 Intern

    •

    12735 Posts

    444

    0

    Posted September 14th, 2007 21:00

    I have heard of no issues with this version, unlike the earlier now removed version.
     
    I recommend flashing in safe mode.
     
    We do not recommend flashing the bios unless it is absolutely necessary to solve a problem.
  • Philip42h

    103 Posts

    444

    0

    Posted September 15th, 2007 05:00

    It does seem quiet ... is no news on BIOS 1.1.11, good news, or are we all to frightened to try it? I'd really like to hear some positive news of success ...  :smileywink:
     
     
    We know that anyone with a C/E521 with a BIOS between 1.1.4 and 1.1.10 has the potential for USB problems depending on what USB devices are plugged in an where ... so it would be rather good to believe that this was resolved in 1.1.11.
     
    Equally, flashing the BIOS on a 521 is a bit like playing russian roulette and many mainboards have died. And Dell haven't really 'fessed-up to this as a problem yet, let alone proposed a resolution.
     
    I did successfully flash from 1.0.3 to 1.1.8 when I upgraded to Vista. At that time the flash would not run it Safe Mode - I tried and it said "this program does not run in Safe Mode" or words to that effect. So I pulled out all the plugs save mouse, keyboard and monitor (no USB or network connection) and rebooted, killed off all the applications running from start-up (including AV), crossed figures and it worked.
     
    There are about 60 days left on my warranty ... I just know that I'm going to have to try it again ...:smileyindifferent:
  • mombodog

    2 Intern

    •

    12735 Posts

    444

    0

    Posted September 15th, 2007 05:00

    "Dell haven't really 'fessed-up to this as a problem yet"
     
    In a round about way they did, they replaced a bunch of motherboards and pulled the offending 1.1.5 bios version from the site.
     
    The only time they failed was when you tried going from 1.1.4 to 1.1.5 all in Vista.
     
    If there are problems with 1.1.11 you would hear about them for sure, it has been 11 days since release.
     
    But you know the saying, If it ain't broke....
  • Reiper

    37 Posts

    444

    0

    Posted September 15th, 2007 16:00

    I went ahead and upgraded the day after it came out... I went from 1.1.8 to the new 1.1.11. I disconnected all connections (modem, internet, etc.) and stopped all apps prior to installation. It was a little scary as the update program just sat there in windows Vista and said not responding. However, I just let it sit there and after about 3 min (very long minutes) it rebooted to the new bios without any problems. Have been running since then without a hitch! If I was going to do it again, I do think doing it in safe mode would be a good idea though. Not sure about the powered hub issue as I don't currently have one but went ahead and did the update anyway as I'll probably add one later. Also, I wanted to do the flash while the computer was still under warranty.
  • 444

    0

    Posted September 15th, 2007 17:00

    I flashed it about 2 weeks ago (from 1.1.10)
    no issues
  • Philip42h

    103 Posts

    444

    0

    Posted September 16th, 2007 06:00


    @gbensonsr1 wrote:
    dose anyone know if the new bios update DME521-010111 is safe to use?

    Unfortunately, I now know that it is NOT safe to use !!!

    It does not run in Safe Mode - immediately reports DME521-010111.exe has stopped working.

    I am currently running it under Vista with nothing but keyboard and mouse connected and no other applications running - I've had the Failurex3 about ten times so far - the best its done is get to 57% before failing.

    At least now when it fails the pop-up window simply says press OK to flash again ... but it does not look as though this is going to work.

    Update: Still failing after after an hour an a half - must be around 30 attempts so far. It looks like a call to support when they open at 8:00 on Monday

    Message Edited by Philip42h on 09-16-2007 03:13 AM
  • mombodog

    2 Intern

    •

    12735 Posts

    444

    0

    Posted September 16th, 2007 20:00

    "Wonder why it took dell so long to fix this problem"
     
    They had to find the root cause, not an easy task i guess.
  • Merek

    3 Posts

    444

    0

    Posted September 16th, 2007 20:00

    I have successfully flashed to the new version, and it has solved the USB problem on my E521. No hanging on boot with USB devices plugged in like before.  I have been able to flash every version that has come out, so I guess I'm lucky about that, as many others have had big problems.  Wonder why it took dell so long to fix this problem.
  • gbensonsr1

    114 Posts

    444

    0

    Posted September 17th, 2007 01:00

    do you think they could do the same for sigmatel line in on the sound card?
  • mombodog

    2 Intern

    •

    12735 Posts

    39

    0

    Posted September 17th, 2007 19:00