UNSOLVED

pastle

updated

22 years ago

P

pastle

105 Posts

0

12101

October 27th, 2004 12:00

Need Help. Very SLOW start up.

My sisters Dell starts up very slow. I'm talking 5 or 10 minutes, maybe more. It started when she installed her scanner and even when she un-installed the scanner, it is still slow. (The scanner is newer than mine so don't see the problem.) After it boots up it runs normal until she has to re-start it.
Does anyone have any idea why this would happen and what to do about it?
  • volcano11

    2 Intern

    •

    27973 Posts

    577

    0

    Posted October 27th, 2004 12:00

    Do any devices that connect by USB have a memory card reader?  If so, then first unplug that USB device before booting and see if that solves the slow boot problem.  If it does, then you will need to go into the BIOS and set the Legacy USB support to No boot (if that option is available) or Disabled.  The problem results from the BIOS looking for a bootable device in the memory card reader.
     
    Steve
  • pastle

    105 Posts

    577

    0

    Posted October 27th, 2004 13:00

    Not sure what a memory card reader would be but she has nothing connected to her PC that I don't have connected to mine and I have no problem.
  • DrChris

    12 Posts

    577

    0

    Posted October 27th, 2004 15:00

    if u are an experienced user, i recommend to click start/run and type msconfig

    by selecting startup, you will see all the applications that run when windows is starting

    ideally, on a formated harddrive with freshly installed windowsxp, there is nothing in there

    you cannot exactly identify what each file does apart from the directory name really; but by unselecting one you will prevent it from starting in the future

    since its the scanner software that might have been causing the problem, i would suggest to unclick whatever was related to it; for example if there is an application that updates the scanner software on startup 

    my advise, do not unselect anything that you dont know what it does, although you can always get back in there and reselect it

    hope this was helpful

    P4 3.4 GHz, 1.5GB DDR2, X800SE, 840Gb HD, 20" TFT

  • pastle

    105 Posts

    577

    0

    Posted October 27th, 2004 16:00

    I am familar with msconfig but hadn't thought of trying that. I will check it out when I go down to my sisters in a couple days. I can't understand why her scanner would cause this problem. It ran fine on her old PC. And it is newer than the scanner that ran previously on the same PC. (The computer used to be mine before she got it and I never had a problem with it.)
  • volcano11

    2 Intern

    •

    27973 Posts

    577

    0

    Posted October 27th, 2004 17:00

    Some scanners and multifunction printers have memory card readers.  You mentioned that the problem began when a scanner was attached.  Unplugging the scanner during bootup wouold verify whether or not the scanner is the problem.

    Steve

  • pastle

    105 Posts

    577

    0

    Posted October 27th, 2004 17:00

    She had already  tried unpluging and uninstalling. The first time she did this the computer booted up normally. Then she needed the scanner and put it back in. When she removed it the second time the boot up remained slow. Now even with the scanner gone it very slow.
  • masterzebra

    23 Posts

    577

    0

    Posted October 30th, 2004 20:00

    in the bios make sure that the cpu speed is set to normal
  • pastle

    105 Posts

    577

    0

    Posted October 30th, 2004 21:00

    Not sure how to check the bios.
  • pastle

    105 Posts

    577

    0

    Posted November 7th, 2004 23:00

    I went into setup and checked the bios. It was already set to normal.