UNSOLVED

Hesser

updated

18 years ago

H

Hesser

20 Posts

0

8547

October 28th, 2008 20:00

Memory reset to default. How to OC?

I had a bad stick of ram that needed replacing. Dell sent me 4 new sticks of the same kind and they were set to the default 800 setting. Is there anyway to set them back to 1066 as Dell had done with the original set? I tried changing the settings through the bios but the variables cannot be changed. Thanks for your help.
  • Davet50

    6 Operator

    •

    14442 Posts

    401

    1

    Posted October 28th, 2008 20:00

    On what system?
  • Hesser

    20 Posts

    401

    1

    Posted October 29th, 2008 03:00

    720
  • Davet50

    6 Operator

    •

    14442 Posts

    401

    1

    Posted October 29th, 2008 10:00

    Boot into the bios and check to see if the option under memory for EPP/SLI is set to on. This is the only way to  Oc the memory on your system. Also note that the memory must be EPP/SLI ready or this will not work.

    Pick up a copy of CPU-z and look at the memory tab and the SPD tab to see how all your memory is running.

     

     

    Message Edited by Davet50 on 10-29-2008 07:59 AM
  • Davet50

    6 Operator

    •

    14442 Posts

    401

    0

    Posted October 29th, 2008 17:00

    Are you positive that your old memory was running a 1066?  If so it appears that dell did not send you the exact same memory as it is only running a 800mhz.

     

    Here is something to try. Pull two sticks out and look at the memory tab in CPU-z. The important listing is the memory frequency. You need to double this as the memory is dual channel. So if it reports the freq at 400 then the memory is running at 800, like wise if it says 533 then the memory is running at 1066.

    Also look at the timings that are listed on the memory tab and compare them to the timings that are listed on the SPD tab. This will tell what SPD the memory is running in and the voltage that it needs. If there is no listing on the SPD tab for EPP then your memory is not EPP/SLI certified.

     

    right now yours is running a 800mhz.

  • Hesser

    20 Posts

    401

    1

    Posted October 29th, 2008 17:00

    Processor(s)

    Number of processors 1
    Number of cores 4 per processor
    Number of threads 4 per processor
    Name Intel Core 2 Quad Q6600
    Specification Intel(R) Core(TM)2 Quad CPU Q6600 @ 2.40GHz
    Package Socket 775 LGA
    Family/Model/Stepping 6.F.B
    Extended Family/Model 6.F
    Core Stepping G0
    Technology 65 nm
    Core Speed 1600.2 MHz
    Multiplier x Bus speed 6.0 x 266.7 MHz
    Rated Bus speed 1066.8 MHz
    Stock frequency 2400 MHz
    Instruction sets MMX, SSE, SSE2, SSE3, SSSE3, EM64T
    L1 Data cache (per processor) 4 x 32 KBytes, 8-way set associative, 64-byte line size
    L1 Instruction cache (per processor) 4 x 32 KBytes, 8-way set associative, 64-byte line size
    L2 cache (per processor) 2 x 4096 KBytes, 16-way set associative, 64-byte line size

    Chipset & Memory

    Northbridge NVIDIA nForce 680i SLI SPP rev. A2
    Southbridge NVIDIA nForce 680i SLI MCP rev. A3
    Graphic Interface PCI-Express
    PCI-E Link Width x16
    PCI-E Max Link Width x16
    Memory Type DDR2
    Memory Size 4096 MBytes
    Memory Frequency 400.0 MHz (2:3)
    CAS# Latency (tCL) 5.0 clocks
    RAS# to CAS# (tRCD) 5 clocks
    RAS# Precharge (tRP) 5 clocks
    Cycle Time (tRAS) 18 clocks
    Bank Cycle Time (tRC) 22 clocks
    Command Rate (CR) 2T

    System

    System Manufacturer Dell Inc.
    System Name Dell XPS720
    Mainboard Vendor Dell Inc.
    Mainboard Model 0P611C
    BIOS Vendor Dell Inc.
    BIOS Version A05
    BIOS Date 01/03/2008

    Memory SPD

    Module 1 DDR2, PC2-6400 (400 MHz), 1024 MBytes, Corsair
    Module 2 DDR2, PC2-6400 (400 MHz), 1024 MBytes, Corsair
    Module 3 DDR2, PC2-6400 (400 MHz), 1024 MBytes, Corsair
    Module 4 DDR2, PC2-6400 (400 MHz), 1024 MBytes, Corsair

    Software

    Windows Version Microsoft Windows Vista (6.0) Home Premium Edition Service Pack 1 (Build 6001)
    DirectX Version 10.0
    Message Edited by Hesser on 10-29-2008 01:07 PM
    Message Edited by Hesser on 10-29-2008 01:09 PM