UNSOLVED

SantAndre

updated

20 years ago

S

SantAndre

4 Posts

0

10076

July 22nd, 2006 18:00

HELP : Is the problem from the computer?

Hi, my father has a DELL Optiplex Gx240 running Windows XP Pro. Recently he had a power failure and lost his System Disk. Fortunately his data was into another partition on that drive and there also was a Ghost image of his installation. Since I could not recover his C: (system) drive, I got a new Western Digital EIDE 250 Gb. Using partition magic on my computer, I partitioned the new drive in two different partitions. One, the Primary DOS NTS formatted of 30 Gb which I reserved for the system and and a second NTFS for his data with approx 215 Gb. From Windows Explorer on my computer I could see the new drive (connected through USB) and both partitions. I could copy the Ghost image (Symantec ver 8) to the second partition and move files around on both partitions. The hard drive was tested with WD diagnostic soft and went through Ok.

I then re-installe de new drive into my dad's computer and booted from a DOS 6.22 diskette. I noticed a message saying that "Primary hard disk drive 0 not found" and "Primary hard disk drive 1 not found" so I went into the BIOS to make sure the drive was active. It was and was properly identified by the BIOS.

I then completed the Boot process and ran the Ghost program from a diskette. Ghost could see the hard disk and I could de-ghost the image I had copied on the second partition to the first partition.

When I rebooted, The computer without a diskette, I stil had the "Primary hard disk drive 0 not found" message.

I can stille see the drive in my dad's computer BIOS, and I can see the de-ghosted files in Windows Explorer on my computer.

So everything is there but the Optiplex does not seem to be aware of it. Since the waranty is over, is there any suggestion from someone of the next step I can take to solve this issue.

By the way, I updated my dad's computer from Phoenix BIOS A01 to A05.

Completely at a loss...
  • ZSS9393

    8 Posts

    540

    0

    Posted July 23rd, 2006 16:00

    If the drive is NTFS, DOS can NOT use the drive. You may end up formatting the drive. DOS 6.22 can not use large disks; 2 gigs or more. But a Windows 95/98/ME Boot disk can view large disks; but not NTFS. NTFS for DOS can! It is free for home use.
  • SantAndre

    4 Posts

    540

    0

    Posted July 23rd, 2006 18:00

    I understand what you are saying about DOS and NTFS but all I meant to point in my explanations is that Ghost could read the second HD partition and write to the first HD partition. In other word, the HD is alive and well and the IDE functionality is perfect. This eliminates two main causes for the message I see when I try to boot the computer : "Primary hard disk drive 0 not found" followed by "Primary hard disk drive 0 not found" which at first sight might indicate a bad disk (not true, Ghost sees it) or secondly a bad IDE cable or defective IDE function (not true since Ghost uses it)...

    Once this is stated, I am left with a system that does not see the hard drive no matter if I try to boot from a diskette, from a CD or from the system Hard Disk (which it does not see anyway and cannot boot from) and my question is : What else could make the system not recognize the healthy HD that I could try to correct???
  • ZSS9393

    8 Posts

    540

    0

    Posted July 23rd, 2006 19:00

    Put the drive in a different computer and use it as a slave.
    Then, format it FAT32 and ghost it from there. OR try to downgrade the BIOS.
    The BIOS may not see NTFS. Just a Guess.
  • SantAndre

    4 Posts

    540

    0

    Posted July 24th, 2006 00:00

    Done that (FAT32 partitioning) with same result. The BIOS sees the drive. When I boot, from diskette or CD, the HD is not recognized in the boot process.

    Problem is from the computer not the drive, not the BIOS.

    But thanks anyway for trying to help.
  • 540

    0

    Posted July 24th, 2006 06:00

    All IDE drives need to be jumpered for cable select and not master or slave.  Do this, then reset the NVRAM to get the drives detected correctly in the bios.

     

     

  • SantAndre

    4 Posts

    540

    0

    Posted July 24th, 2006 10:00

    This has been done and if you read correctly what I said, BIOS detects the drive. The problem comes up later.
  • phimuskapsi

    2 Intern

    •

    132 Posts

    540

    0

    Posted July 25th, 2006 13:00

    My guess is that you mentioned it's a USB drive. Look for a USB legacy support option in the BIOS. This may need to be turned on. Most people do not use USB drives as bootable drives for just this reason.