UNSOLVED

RobbieB

updated

13 years ago

R

RobbieB

37 Posts

0

112395

May 24th, 2013 12:00

factory restore optiplex 320 - problem

I just tried to factory restore using the dell utility on my moms Optiplex 320.

Everything seemed to go fine and after it said finished, the system rebooted and all I got was a black screen and a mouse cursor. Waited about 15 minutes and still nothing. I pressed the power button, after it shut down, pressed again, it said resuming windows. What's going on, did the restore process just hose her computer? Is there a way to initiate it again via command prompt or something?

  • DELL-Amogh G

    6 Operator

    •

    1499 Posts

    2357

    0

    Posted May 24th, 2013 12:00

    Hi RobbieB,

    I would suggest you to drain the residual power from the system:

    • Disconnect any external peripherals (flash drives, printers, external hard drives) from the computer
    • Press and hold the power button for 10 seconds.

    You may run the hardware diagnostics to check the hardware functionality. please follow the steps below:

    • Reboot and press F12 to enter the Boot Menu
    • When the boot device list appears, highlight Diagnostics and press Enter
    • The computer begins to run the Pre-boot System Assessment, a series of embedded diagnostics that perform initial testing on your system board, keyboard, hard drive, and display
    • In case any hardware component is bad, you will get a corresponding error.

    Please share the operating system.

    Keep me posted with the results. I will be glad to assist you further.

  • RobbieB

    37 Posts

    2357

    0

    Posted May 24th, 2013 12:00

    When I tried powering off/on again, this time I noticed some kind of resume message and it said I could press space bar, so I did. Then I was presented with 2 choices

    continue with system resume

    delete restoration data and proceed to system boot menu

    continue  this brings me to the same problem i had, black screen with cursor only.

    delete seems to be about the same, black screen but no cursor

    either way I'm still left without a functioning computer... I'm in the process of downloading a win7 home premium iso. But it would be nice if the restore process actually worked

  • RobbieB

    37 Posts

    2359

    0

    Posted May 24th, 2013 13:00

    This isn't a laptop

  • RobbieB

    37 Posts

    2359

    0

    Posted May 24th, 2013 13:00

    I ran diagnostic, everything was passing, but then it said

    Incompatible video controller.

    Vesa function 0x4f02 returned AX = 14f

  • DELL-Amogh G

    6 Operator

    •

    1499 Posts

    2359

    0

    Posted May 25th, 2013 12:00

    Hi RobbieB,

    Usually this error comes up when the system is stuck in hibernation. You may open the system tower, take out a memory card and then try to power on the system on a single memory card and check if it works. You may put the first memory card back and take out the second memory card and then restart it. For Owner’s Manual, please refer to the link: http://bit.ly/12qMBlT.

    Keep me posted with the results. I will be glad to assist further. 

  • RobbieB

    37 Posts

    2359

    0

    Posted May 28th, 2013 13:00

    I downloaded windows 7 home premium 64bit iso and reinstalled.

    The system booted up successfully. After downloading networking drivers from dell.com I was able to get online and run windowsupdate. After performing all updates and restaring. I encountered the SAME exact issue.

    System turns on, you see the loading screen. Then a black screen and cursor only.

    The system only has 1 memory module of 4gb. I did remove it. Attempt to boot until I heard the beeps when it failed to post.

    I reinserted the module and booted up. Got the warning about previous boot attempt had no memory, I hit f1 to continue.

    It still presented me with a black screen and only a cursor. for the heck of it, I decided to hit enter on the keyboard, and type in the users password, it logged me into the system and I was able to see parts of the desktop.

    the top and bottom half of the screen are still black

    Pressing the windows key, or windows +r does not do anything. Pressing Ctrl Alt Del brings the black screen and cursor back.

    soo frustrating.

  • RobbieB

    37 Posts

    2359

    0

    Posted May 28th, 2013 14:00

    I cannot press Windows+Pause/Break key either. I can right click desktop and that's it. I can view resolution settings etc.

    From there I can navigate to control panel or any file/folder but for instance if I navigate to c:\program files (86)\internet explorer, I am unable to launch iexplore.exe, it simply doesn't do anything.

    I can boot into safemode with networking. I can browse the web just fine. I attempted to download the video driver but when I tried to install (via safe mode) I got a message saying something like your computer does not meet the requirements to install.

  • DELL-Amogh G

    6 Operator

    •

    1499 Posts

    2359

    0

    Posted May 29th, 2013 12:00

    Hi RobbieB,

    You may make changes to the system BIOS, that should help. Please follow the steps below:

    • Power on the system and tap 3-4 times at Dell logo.
    • System Setup Utility will open up.
    • Go to ‘Onboard Devices’ at left hand side
    • Go to ‘USB controller’
    • Set it on ‘No Boot’ option.
    • Press to ‘Save Changes and Exit’

    Keep me posted with the results. I will be glad to assist. 

  • speedstep

    11 Legend

    •

    46969 Posts

    2359

    0

    Posted May 29th, 2013 12:00

    I downloaded windows 7 home premium 64bit iso and reinstalled.

    The system booted up successfully. After downloading networking drivers from dell.com I was able to get online and run windowsupdate. After performing all updates and restaring. I encountered the SAME exact issue.

    System turns on, you see the loading screen. Then a black screen and cursor only.

    The system only has 1 memory module of 4gb. I did remove it. Attempt to boot until I heard the beeps when it failed to post.

    I reinserted the module and booted up. Got the warning about previous boot attempt had no memory, I hit f1 to continue.

    It still presented me with a black screen and only a cursor. for the heck of it, I decided to hit enter on the keyboard, and type in the users password, it logged me into the system and I was able to see parts of the desktop.

    the top and bottom half of the screen are still black

    Pressing the windows key, or windows +r does not do anything. Pressing Ctrl Alt Del brings the black screen and cursor back.

    soo frustrating.

    The 320 Does not support 4 gig modules.  It supports 2  modules of 1 gig and with updated bios 1 of 2 gig.

    It will not work with 4 gigs of ram Ever. (2Gig Modules work but only 1 at a time.) If you put 2 in its dead.

    Windows System restore is not factory restore and the CTRL F11 restore is for Dimensions not Optiplex.

    The video on the 320 is the Radeon Xpress 1100 Driver.  The newest Driver does not work due to ATI not supporting Radeon Xpress 1100 Video.

    The latest driver is Legacy Display Driver for windows vista. No driver for windows 7 is available.

    You can download the driver and install them in compatible mode. Here is How to.

    http://support.amd.com/us/gpudownload/windows/Legacy/Pages/integrated_vista64.aspx?type=2.7&product=2.7.5.3.3&lang=us&rev=9.11&ostype=

    Name File Size Revision Number Release
    Date
    Download
    Link
    Catalyst Software Suite 95 MB 10.2 2/24/2010 Download


  • RobbieB

    37 Posts

    212

    0

    Posted June 3rd, 2013 09:00

    This computer has never been upgraded or modified. It was ordered directly from dell.com. So if

    1) 4 GB modules are not supported

    2) video card is not supported in windows 7

    Why would they sell it in this configuration?