UNSOLVED

Phil1234

updated

21 years ago

P

Phil1234

2 Intern

•

349 Posts

0

11554

September 26th, 2005 13:00

Extra Drive Rails XPS Gen 5

Congrats Dell on a forum just for XPS systems :smileyhappy: I Just noticed this new forum and thought I would ask this question here as nobody has been able to give any concrete advise on the other forums.  I am awaiting a new XPS Gen 5 with no floppy drive, but it has dual 160 GB sata drives.  Can a Gen 5 owner confirm that the there are extra rails for installing a floppy after the fact and are the extra rails for a 3rd hard-drive.  I've read the manual and there is nothing that states it ships with them only text on removing current rails from a faulty drive to install on a new drive.  My older 8250 shipped with extra rails a few years back already fastened to the interior of the case.  Thanks.
 
Phil.
  • PsychoT

    62 Posts

    212

    0

    Posted September 26th, 2005 21:00

    I opened my system up the other day.  They DO come with extra drive rails.  they are in the Hard drive and optical bays not attached to the chassis like the older systems.
  • Phil1234

    2 Intern

    •

    349 Posts

    212

    0

    Posted September 26th, 2005 22:00

    Thank you for the update.  It is appreciated.  Have a great evening.

    Phil.

  • CTskydiver

    1 Rookie

    •

    932 Posts

    212

    0

    Posted September 28th, 2005 08:00

    The systems ship complete with drive rails for each empty bay (Gen-5 and 600, since I've one of each flavor) except the floppy bay. One snag I noticed though - I couldn't fit a hard drive in the (empty) floppy bay on top with the provided rails - they are too thick (or the bay is too small) buy just a smidge. I had some rails from a Dimension 8250 that did the trick though.

    I'd have been upset if I couldn't make use of the floppy bay for an additional hard drive, so it was lucky I had the rails. I was hoping to put the memory card reader there, but the floppy bay has no removable face plate (it's molded out of the whole front of the case) - which means it is a floppy bay or a jury rigged hard disk bay, and nothing else. Bummer to waste a 5" bay with the little memory card reader, but I like having it onboard.

    Dimension XPS 600, WinXP MCE'05
    Pentium D 830, 2 GB 677mhz DDR2 SDRAM (2 Dimms)
    256 MB nVidia GeForce 6800, SoundBlaster Audigy 2ZS
    One DVD Burner (16x +-RW,DL), TVT3 Dual Tuner, Dell 9 in 1 Reader
    1.3 TB Total Hard Disks (SATA-150 300, 300, 250GB) (IDE UATA-133 250,200GB)
    (via a Maxtor combination SATA/IDE PCI RAID Controller, a power cable splitter
    & a pair of aftermarket rounded IDE ribbon connectors)
    2 Dell 1905FP 19" Digital Flat Panel Displays

    Message Edited by CTskydiver on 09-28-2005 05:11 AM

    Message Edited by CTskydiver on 09-28-2005 05:12 AM

  • Phil1234

    2 Intern

    •

    349 Posts

    212

    0

    Posted September 28th, 2005 10:00

    Thank you very much, that is great news.  I also have an 8250 that I can rob drive rails from if needed.  That is quite a nice XPS600 you have spec'd there :smileyhappy: Again, thank you for your reply.

    Phil.

  • joer45

    11 Posts

    212

    0

    Posted September 29th, 2005 17:00

    Hey i noticed that you installed extra ide drives into ur pc..  By any chance do u have a link for the power convertor  (sata power to a 4 pin power) inorder to connect the ide drive with the sata power.  Right now im running my extra ide hd power off of my dvd drives power but if possible i wanna run it off a single power source.  

    Message Edited by joer45 on 09-29-2005 01:41 PM

  • CTskydiver

    1 Rookie

    •

    932 Posts

    212

    0

    Posted September 29th, 2005 18:00

    Nah, sorry. I'm using y-adapters (splitters) that turn one 4-wire plug into two 4-wire plugs. $3 a pair at CompUSA.

    I had in my previous system an adapter that goes from 1 IDE power -> 1 SATA power that I used to power a couple SATA drives in an IDE system (with a Maxtor PCI-SATA card).

    I didn't see any at the store though that go the other way, though, so the splitters were my only option. You might find them online though, I'm sure somebody must make them.
  • joer45

    11 Posts

    212

    0

    Posted October 1st, 2005 20:00

    Well i gave in and im jsut gonna buy an enclosure for my ide drive and run it externally, and i jsut bought 2 raptors to run on raid so hopefully I'll be able to really unleash the power of this bad boy.  I just was hoping this system had more than 3 drive bays to install hd's, and the 9 in 1 reader is nice and all but i would of rathered an external usb one so i could use the 3rd drive bay for a fan controller.  What kills me is how fast they already jumped into making a gen 6 that has the dual sli option.. If I would of known i would of held out the extra month.

    Message Edited by joer45 on 10-01-2005 04:47 PM

  • CTskydiver

    1 Rookie

    •

    932 Posts

    212

    0

    Posted October 2nd, 2005 03:00

    As far as the card reader, I would have preferred it to have been intergrated into the case, like the front audio/usb/firewire ports were, not taking up a drive bay OR space on my desktop - kind of like they are on this HP ->

    http://images.bestbuy.com/BestBuy_US/images/products/7264/7264015_ra.jpg

    Oh, well. All in all - I'd still chose the Dell, so I can't really complain there.

    I only wound up with the XPS 600 because I bought a Gen-5 a day or two before the option to do so was removed from their web site. At the time, I could have chosen either system.

    My computer was "obsolete" before I even unpacked it - as I found out when I tried to have it exchanged for a like model (minus the damage) and discovered like models were no longer available. "Too bad, so sad," said Dell. Customer service aparently expired with the Gen-5.