UNSOLVED

jlscottlp

updated

25 years ago

J

jlscottlp

8 Posts

0

7405

December 14th, 2001 13:00

DMA Problems

I have an 8100 1.5 Ghz with a clean install of Wxp Pro. The computer has a Maxtor HD, Zip drive, CD and CDRW drives.
All the drives work well without any problems.
My IDE/ATAPI Controller lists the Primary and secondary channels. In the advanced settings of the Primary IDE channel, the first device (Device 0) shows that it is using Ultra DMA Mode 5, and the second device (Device 1) shows that it is using PIO only. The secondary channel shows both devices using Ultra DMA 2.
The primary's 2nd device can be changed to use Ultra DMA but it defaults back to PIO. Is this a problem with one of the drives or XP? Thanks for any info...


  • Karell

    2 Intern

    •

    2544 Posts

    411

    0

    Posted December 14th, 2001 16:00

    Jlscottlp,

    Thank you for using the DellTalk forum.

    It sounds like the secondary device on the primary IDE
    cable is your zip drive. I am not sure if zip drives support
    DMA access or not. You may want to try and find this
    out on the Iomega web page. You can also download the
    latest Iomega ware software, and install it to see if that
    fixes the problem. If that does not fix the problem, move
    the zip drive to the master device on the secondary IDE
    cable, move your CDROM drive to the slave device on your
    primary IDE cable, and see if you can enable DMA for the
    zip drive then.


  • jlscottlp

    8 Posts

    411

    0

    Posted December 14th, 2001 16:00

    I downloaded new files from Iomega and it did not solve the problem. When I check under Policies for the Zip drive, it has a check mark in "Enable write caching on this drive", and the box is grayed out, making it unable to change. It also has a yellow triangle beside it with the notation "This device does not allow write caching to be disabled. A power outage or equipment failure might result in data loss or corruption."
    How do I change the locations of these devices?
    Thanks for your help...

  • Karell

    2 Intern

    •

    2544 Posts

    411

    0

    Posted December 14th, 2001 17:00

    Jlscottlp,

    On the Iomega web page, the transfer rate for the
    Zip and Zip250 is (26.7Mbits). This transfer rate falls
    under the ATA standard, which does not support DMA.
    I also cannot find any documentation for the Zip or Zip250
    stating that they support DMA transfers. I would simply
    say that they do not support DMA.

    If you want to switch the orientation of the drive connections,
    you would have to open the system case, disconnect the
    zip drive from the secondary connector on the primary IDE
    cable. Disconnect your CDROM, from the primary connector
    on the secondary IDE cable, and switch the 2 connections
    around.

  • dre53

    396 Posts

    411

    0

    Posted December 14th, 2001 18:00

    You should leave everything alone. Your cd and cd-rw are correct, dma 2, your HD is correct dma 5, your zip drive is correct, it does not support dma.

    Pentium 4 1.9 Gig / 478 pin 400Mhz FSB
    Shuttle Motherboard
    Via chipset P4x266 VT8233 DDRam Support
    Windows XP (home edition)
    DDRam 768 Meg
    WD 80 gig HD ATA 100
    Gainward GF3 Powerpack Golden Sample/64 meg
    LiteOn 24x10x40 CD-RW
    Pioneer DVD 500m
    Pinacle Firewire Card
    Santa Cruz Sound Card (4127 beta drivers)
    Linksys Lan Card
    Dell 991 Monitor
    Microtek 3700 Scanner
    HP 1100 Printer
    Logitech Pro 3000 web cam

    Other:
    XPSB1000r
    XP home
    384 megs PC700 Rdram
    60 gig maxtor HD
    DVD-Rom
    Sony CD-RW
    Gforce 2 pro 64meg
  • jlscottlp

    8 Posts

    411

    0

    Posted December 14th, 2001 20:00

    This problem I'm sure is what's causing the Warning message in the system event viewer everytime I re-boot. "The driver disabled the write cache on device \Device\Harddisk1\DR1." I guess XP is loading the write cach driver for the Zip 250 and then disabling the driver. I was hopeing to get rid of the warning message but I can't figure it out. Thanks for all your help....

  • Karell

    2 Intern

    •

    2544 Posts

    411

    0

    Posted December 17th, 2001 12:00

    Jlscottlp,

    I did some digging, and I found an article on this problem.
    The problem is a glitch between Windows XP and the Zip 250.
    There is no actuall damages or data loss that happens.
    It is simply displaying an *annoying* error message.
    As of yet, there is not solution for this problem. The solution
    would either have to come from Microsoft, or Iomega.
    ---------------------------------------------------------------------------------------
    Iomega Zip 250 causes entries in Event Viewer in Windows XP

    Problem: After copying a file to an Iomega ZIP250 drive, warnings may appear in the Windows XP Event Viewer.

    Discussion: The event viewer warning states:
    The driver detected that the device \device\harddisk\dr1 has its write cache enabled. Data corruption may occur.
    By default the write cache on the Iomega Zip250 is enabled. When files are copied to the Zip250 drive, the write cache may not be cleared immediately. However, as long as the system is properly shut down no data loss should occur.
    Of course, if the system is not shut down normally, data corruption may occur.

    Solution: It is not necessary to do anything about the warning message. The ZIP drive is behaving correctly and according to manufacturers specifications.
    There is no solution for this error message at this time.
    The error message will not affect the performance of the system.

    To prevent data corruption, always shut down the system normally. Also, properly ejecting any ZIP disks in the ZIP drive will ensure that no data corruption occurs. If the system is improperly shut down and the ZIP disk is ejected using the emergency eject method, the data on the ZIP disk may be corrupted.
    ----------------------------------------------------------------------------------------