UNSOLVED

tdark

updated

20 years ago

T

tdark

2 Intern

•

222 Posts

0

22009

September 21st, 2006 21:00

Dimension power supply question

I have a dead power supply on a Dimension 4550. Will any ATX  P4 ready power supply work?  The Dell has the regular 20 pin connector that is used on all ATX boards I have worked on but one wire is missing(the white -5volt wire),so it really has only 19 wires.  The Antec ATX I have has 20 wires and  the white wire. What damage if any would it do If I connected it to see if the system would power on. Tom
  • tdark

    2 Intern

    •

    222 Posts

    422

    0

    Posted September 21st, 2006 21:00

    My question is will it hurt anything to plug my antec 20 pin P4 power supply to see if it will power up??
  • DELL-Donald K

    2 Intern

    •

    3969 Posts

    422

    0

    Posted September 21st, 2006 21:00

    I'm pretty sure the 4550 power supply is proprietary, Dell started using standard ATX power supplies in the 4600.
     
    You might want to try www.pcpowercooling.com
     
     


    DELL-Donald K
    #IWork4Dell

  • ejn63

    11 Legend

    •

    87469 Posts

    •

    321256 Points

    422

    0

    Posted September 21st, 2006 22:00

    Except that the case has no space for an on-off switch on it, the power supply is standard ATX.
  • shesagordie

    12 Elder

    •

    46017 Posts

    422

    0

    Posted September 21st, 2006 22:00

    tdark
     
    Yes, it will work, the D-4550 uses a standard 20-pin ATX power supply, without the on/off switch. If you want to install a unit with the switch, then you will have to cut a hole in the back panel for the switch.
     
    Bev.
     
     

    Message Edited by shesagordie on 09-21-2006 06:16 PM

  • tdark

    2 Intern

    •

    222 Posts

    422

    0

    Posted September 22nd, 2006 01:00

    Thanks to all. It does not have the on/off switch so it should work. It did power on by the way. I just wanted to make sure. I had read a few years ago that some Dells came with different power supplies and if a standard ATX was connected it would fry the board. Thanks again    Tom
  • shesagordie

    12 Elder

    •

    46017 Posts

    422

    0

    Posted September 22nd, 2006 03:00

    tdark
     
    That's great.  :)
     
    Dell Dimension systems, 2200,2300,4300,4400,4500, 8200, and above, the power supplies [20-pin] are to ATX standard, that have been modified, by having the power on-off switch removed.

    The PSU's in the Dimension systems, prior to these systems are not standard and are proprietary.

    The Dimension 4700, 8400 systems and above, use the newer 24-pin motherboard connector standard power supplies.

    Bev.
  • vosamis

    55 Posts

    422

    0

    Posted September 22nd, 2006 19:00

    Holy cow, to replace the power supply from that cooling web site, it costs $150! and tbat does not include tax and shippping, which is likely another $20. For a power supply, that's nuts.
  • tdark

    2 Intern

    •

    222 Posts

    422

    0

    Posted September 24th, 2006 19:00

    Bev, one more question. Should I just leave the white wire that comes on the   standard ATX connected to this Dell board or cut it. The original Dell power supply had the 20 pin connector but the white wire was not there. According to what I have read the white wire has -5volts and should not hurt anything but wanted to be sure. Thanks for your help. Tom
  • tdark

    2 Intern

    •

    222 Posts

    121

    0

    Posted September 24th, 2006 19:00

    Thanks again, I installed it and all is great. This site is great. Thanks again for your time. Tom
  • shesagordie

    12 Elder

    •

    46017 Posts

    422

    0

    Posted September 24th, 2006 19:00

    tdark
     
    Just leave it alone, it should not harm anything.
     
    Bev.