UNSOLVED

Dman566

updated

12 years ago

D

Dman566

7 Posts

0

119609

May 29th, 2014 22:00

Dell Studio XPS 8100 PSU and GPU upgrade:

I'm new to this site, but from doing some research I feel like I can get a ton of info from here.

I'm trying to upgrade my Dell Studio XPS 8100 for proper gaming and CAD work.

Current Configuration: 
i7-860 @ 2.80GHz
8 GB ram
ATI Radeon HD 5450
350 W PSU

Before I go out and buy the parts (PSU and GPU) I was wondering if anyone who has upgraded these parts already can help in terms of finding a proper size and model component for the 8100 case. 

From doing some research I read that the Corsair CX Series 750W Power Supply fits fine. Anyone have any experience with this PSU or have used another model that has worked?

Additionally, I had the Sapphire R9 270X in mind (if anyone could comment on if this would work/fit or maybe another GPU that worked for them.)

Lastly, I also read that the CPU (i7-860) would not bottleneck my GPU (r9-270x). Is this true?

Thank-you for your time

  • osprey4

    6 Operator

    •

    34230 Posts

    1504

    0

    Posted May 31st, 2014 04:00

    Hi Dman566,

    That PSU should be fine provided it has the necessary 6-pin PCI Express connector.

    I'm giving you a bump hoping Kelbear chimes in.

  • Dman566

    7 Posts

    1504

    0

    Posted May 31st, 2014 16:00

    Thank you for the reply.

    Yeah I'll have to check for that. Any extra input would be very helpful, just don't want to go and buy the parts and figure out later that it won't work.

  • Kelbear1

    1524 Posts

    1508

    0

    Posted June 1st, 2014 11:00

    The Corsair is fine even though a 650 watt would be plenty for the R9 270X.  The CX600 modular is only $10 less than the CX750 right now so it's your choice.  The 600W does get the Guru3D Recommended Award which is a good thing and you have the benefit of the modular design.  

    This card takes two PCIe 6 pin connectors.  Most all power supplies over 500 watts have these including the Corsair.  The i7-860 should still be good enough not to have a bottleneck with this GPU.  

  • Dman566

    7 Posts

    1508

    0

    Posted June 1st, 2014 15:00

    Ok makes sense. After doing some reading I found that apparently the CX model isn't as good as both the TX or AX models. Is there a noticeable difference? 

  • Kelbear1

    1524 Posts

    1508

    0

    Posted June 1st, 2014 18:00

    Correct.  The CX line is their lower line of power supplies.  I have the TX 650, but I really don't know how you would tell a noticeable difference in a power supply.   If you were to run two or more video cards or a top-of-the-line card at $400 or more, I would get one of the better models.  In your case, I would not have too much concern about it.  The warranties are longer in the better units, but a 3 year warranty should be good enough. The CX600 HERE is only $37.99 after a $20 rebate which makes it a pretty good deal if you're not looking to spend too much and still get a quality unit.  For the most part, a power supply will last many years.  I have had power supplies fail, but always within the first year so they were covered under warranty and replaced with something equal or better.  

  • Dman566

    7 Posts

    1508

    0

    Posted June 1st, 2014 20:00

    Oh makes sense. My only problem with the CX models is there non-modular. So my concerns with what to do with all wires, not sure if its going to fit well in the 8100 case. 

  • Kelbear1

    1524 Posts

    1508

    0

    Posted June 2nd, 2014 09:00

    The CX600 HERE is a modular unit.  However, it's a hybrid like a lot of less expensive ones and not full modular so you have to be aware of this.  The RM series are full modular.  It's mostly a concern about the length of the wires since all retail power supplies are designed to fit even in a full tower case and they are much, much bigger than the Dell mini towers.  Having a hybrid or full modular unit should help though.  You will still have to tie up the length or stuff them in an open optical bay like I have done in the past.  The wires on the Dell PSU are just cut to fit the case so you will have a lot of extra wire to hide even with a modular.  The CX600 modular just has the 24 pin and CPU cable mounted which you are going to use anyway.  Everything else you can attach as needed. Outside of the sheathed 24 pin connector, they use flat cables which are going to be easier to use.  If you want to keep your cost down and want a modular, I would recommend the CX600M.  It's more than enough for the R9 270X.  

  • Dman566

    7 Posts

    1508

    0

    Posted June 2nd, 2014 16:00

    Yeah I wouldn't need a full modular. Especially if the only two cables actually attatched are the 24-pin and the CPU cable. 

    Stupid questions, but does newegg.com ship to Canada?

  • vfrmark

    2 Posts

    1508

    0

    Posted September 6th, 2014 12:00

    Dman566,

    How did you get on fitting a R9 270X to the XPS 8100 ?   I posted a question here and got a reply that the 270X does not work with a 8300 due to bios issues.

    Just need to find someone that has actually fitted it and its working

    thanks

  • Dman566

    7 Posts

    348

    0

    Posted September 8th, 2014 11:00

    Hey VFRMARK,

    I actually was able to complete this upgrade a while ago. However,  I did not use the r9 270x instead I used the GTX 770 as it proved to be a better video card for my purposes. The GTX 770 was a tight fit but I managed to get it to fit in the small XPS 8100 case. I assume the r9 270x will be the same. 

    In terms of the BIOS issues, I'am not sure. I have the 8100 and the GTX 770 worked perfect with it after I installed the drivers. 

    Additionally, I used a 600W modular power supply, since the default 350W power supply is an ATX, the new one fit with little to no problems (I originally put in a non-modular and had trouble with all the extra chords.)

    Lastly, I added an SSD and made it my initial drive (with windows on it) and moved the original 1 TB as a secondary storage.

    Hope that answers any questions, if you have more don't hesitate to ask. I know when I was building it I was looking for all the help I could get to make sure it would fit before I actually went ahead and did it.