UNSOLVED

denistran

updated

16 years ago

D

denistran

4 Posts

0

29485

August 13th, 2010 23:00

Dell Dimension 9200 start up problems.

So after finding the problem with my desktop which can't not turn on, I assumed that the mobo was dead( this was after a lot of research so I was pretty sure). I went ahead and order a new Mobo for dimension 9200 which is the same version as the broken one. After replacing the mobo, plug in all the devices, double check everything, the computer turn on, Dell bios run , but windows can not start with a BSOD.

I restarted the computer to see what fail. Here is what it say : "Previous fan failure, system battery voltage is low ( this only appear after i unplug and plug in back the battery) . System does not support the installed professor ". Also the diagnosed lights 1 2 3 are steady .

I check the core for all the fan, all have been plug in. Battery is in place. But since i replaced the mobo, i assume the problem is the bios or professor.

Any help would be appreciated. Do i have to format the comp? which i don't want to.

Thanks

Denis

  • fireberd

    11 Legend

    •

    33399 Posts

    •

    112848 Points

    477

    0

    Posted August 14th, 2010 05:00

    It sounds like the replacement motherboard does not support the Processor (not Professor) that you have or the replacement board is defective.

    Inspiron 16 5630 Laptop and WD22TB4 Docking Station
    Self-built desktop for recording studio application
  • shesagordie

    12 Elder

    •

    46017 Posts

    477

    0

    Posted August 14th, 2010 10:00

     denistran

    Dennis.

    Check the BIOS version that's installed in the replacement motherboard, with version 2.5.1, new CPU support was added.

    Bev.

  • denistran

    4 Posts

    477

    0

    Posted August 14th, 2010 11:00

    I just check the Bios version of the replacement motherboard, it's 1.0.1 . it's a brand new , so yeah. Is there any way to update bios without going to Windows ? I can go to the blue set-up screen when the computer start.

    Thanks for helping  :)

  • denistran

    4 Posts

    477

    0

    Posted August 14th, 2010 22:00

    I'm still looking for a way to update Bios. I've been trying to boot and install by USB, but seem like Dos can't find the xxx.exe to run the update. If anyone know the way, please help.

    Thanks

  • dcgtls

    2 Intern

    •

    940 Posts

    477

    0

    Posted August 17th, 2010 11:00

    You might try the 2.3.1 version, it has an option to install from Dos. The link is for the XPS 410 which is the same computer as the 9200 and the bios is the same. If it works you might be able to get into windows or at least safe mode and update to the newest 2.5.3

    http://support.dell.com/support/downloads/download.aspx?c=us&cs=22&l=en&s=dfh&releaseid=R152109&SystemID=DIM_PNT_9200_XPS_410&servicetag=&os=WW1&osl=en&deviceid=308&devlib=0&typecnt=0&vercnt=11&catid=-1&impid=-1&formatcnt=0&libid=1&typeid=-1&dateid=-1&formatid=-1&source=-1&fileid=202515#3DOS

     

  • dcgtls

    2 Intern

    •

    940 Posts

    477

    0

    Posted August 17th, 2010 11:00

    The only way that you will be able to update the bios at this point is to find a CPU that was supported with the old bios and use that to load windows. Where did you get the new motherboard? They may be able to work with you, you might have to send the board back to them and they will install the newest bios.

    Hopefully you know someone that has one that you can borrow for a short time.

    Good luck.

  • denistran

    4 Posts

    477

    0

    Posted August 17th, 2010 12:00

    Thanks for your reply.

    Somehow i was able to get into Windows while finding a way to flash the bios via CD or USB. So i just have to flash the bios through Windows and it went smoothly. However, do i have to update to 2.5.3 version? bc I just update to 2.3.1 right now and it work fine without any problem, except it always ask me to "press F1 to continue" when the computer start, it's not a problem to me thou.

    Again,thanks for all your help. I'm just glad one day the system decided to get into Windows without a BSOD.

  • shesagordie

    12 Elder

    •

    46017 Posts

    477

    0

    Posted August 17th, 2010 13:00

     denistran

    BIOS version 2.5.1 has the added support for processors, personally I would upgrade the BIOS to the latest version, if only to get rid of the 'press F1 to continue' nag.

    But, it's your choice.

    Bev.

  • 477

    0

    Posted October 26th, 2010 17:00

    You might try the 2.3.1 version, it has an option to install from Dos. The link is for the XPS 410 which is the same computer as the 9200 and the bios is the same. If it works you might be able to get into windows or at least safe mode and update to the newest 2.5.3

    http://support.dell.com/support/downloads/download.aspx?c=us&cs=22&l=en&s=dfh&releaseid=R152109&SystemID=DIM_PNT_9200_XPS_410&servicetag=&os=WW1&osl=en&deviceid=308&devlib=0&typecnt=0&vercnt=11&catid=-1&impid=-1&formatcnt=0&libid=1&typeid=-1&dateid=-1&formatid=-1&source=-1&fileid=202515#3DOS

     


    Thanks for your answer! This is what I'm looking for, The link you provided is very useful.