UNSOLVED

BeyondBeige

updated

15 years ago

B

BeyondBeige

15 Posts

0

46035

November 21st, 2011 11:00

Dell 540s Studio - error code or BIOS quirk?

Dell Studio 540s has recently started beeping at boot-time.  Generally* the beep sequence is:

beepbeep----beep     (long pause)      BEEP

Where BEEP is louder, deeper (and I think slightly longer) than a “beep”.  The BEEP is as I would expect from POST.  Sequencing these with the boot-screen displayed therm-bar  beepbeep----beep occurs at the start (or during the first 5-20%); BEEP occurs as the therm-bar completes.  Beeps occur both on cold boot, and on reset.

The downloadable manuals http://support.euro.dell.com/support/edocs/systems/STD540s/en/index.htm don't appear to include definitions for beep codes.  Googling, the beeps don't match any of the code listed here <ADMIN NOTE: Broken link has been removed from this post by Dell>

* I used the word “generally”, as I can change the beep sequence(!).  As per this post http://en.community.dell.com/support-forums/desktop/f/3514/t/19239433.aspx?PageIndex=2 adding or removing USB devices changes the beeps.  Removing all USB gives:
beep                  (long pause)      BEEP

Running the built-in Dell Diagnostics Utility (32-bit) the computer passes, with no issues detected.
MemTest86 v4.0a also passes all 4Gb of installed RAM.
Finally I have tried downloading and upgrading the BIOS, but the installed BIOS is the same or more recent than the download.

So, is there something I've missed; is this beep code something I need to worry about, eg a sign of impending failure; or just a non-documented “feature”?
{Although, if a feature, this does raise the question, why has it only recently started happening?}

  • osprey4

    6 Operator

    •

    34230 Posts

    871

    0

    Posted November 21st, 2011 17:00

    Hi Beyongbeige,

    Does the system start up?

  • BeyondBeige

    15 Posts

    871

    0

    Posted November 21st, 2011 23:00

    Hi,

    Yes the system starts, but at each boot (or re-start) there's the beep code.

  • osprey4

    6 Operator

    •

    34230 Posts

    871

    0

    Posted November 22nd, 2011 04:00

    Since the hardware checks out, I would boot to the BIOS, write down your important settings, then reset BIOS defaults. Boot and see what happens, then go back into the BIOS and re-enable the previous settings.

  • BeyondBeige

    15 Posts

    871

    0

    Posted November 22nd, 2011 05:00

    BIOS re-set has had no effect the start-up beeps.

  • osprey4

    6 Operator

    •

    34230 Posts

    871

    0

    Posted November 22nd, 2011 07:00

    I would look very carefully through the various BIOS screens to make sure the settings match your hardware, particularly the drive configuration and memory configuration. If there is a BIOS setting for quick boot, disable that so you can see any POST messages.

  • BeyondBeige

    15 Posts

    871

    0

    Posted November 22nd, 2011 09:00

    BIOS tools don't give the flexibility they once did (ok, I expect this is because its Dell specific, and the more powerful controls removed from the user and pre-configured).

    Quick Boot control exists but does not allow the POST screen to appear - no control for turning off Dell's therm-bar boot screen to show us what we need to see.

    Very sanitised "memory info" screen, shows overview of what's installed but no technical details and no user changeable settings.  Hard disk is very similar, its either detected or its not; no user options or overrides.

    Under Advanced setting there are some CPU configuration options, nothing major and all are set correctly.

    I have also checked other settings, integrated peripherals; chipset; power management, but again none offer any control that would allow the user to upset the machine if set incorrectly.  At least after re-set all settings appear to be set in a logical manor, and I can see no conflicting logic between them.

  • speedstep

    11 Legend

    •

    46969 Posts

    871

    0

    Posted November 22nd, 2011 11:00

    Therm Bar and beep slowing sounds like CPU throttling.  I would see if there are Overheating logs in the bios event log and or in the windows event log.

  • speedstep

    11 Legend

    •

    46969 Posts

    871

    0

    Posted November 23rd, 2011 07:00

    If you hit space bar on the keyboard that "Therm Bar usually bypasses" some tests and goes faster.

    Bios is basic but some models have an event log in the bios.  I don't own your specific model so I wouldn't  know that. 

    Fast Boot may be another avenue.

    Boot Settings Configuration

    Configure Fast Boot, Numlock and Keyboard errors.

    You could try clearing cmos.

    Locate the 3-pin CMOS jumper (CLEAR_CMOS) on the system board (see System Board Components

    <ADMIN NOTE: Broken link has been removed from this post by Dell>). 


    Back to Contents Page

    Entering System Setup

    1. Turn on (or restart) your computer.

    2. When the blue DELL™ logo is displayed, watch for the F2 prompt to appear and then press immediately.

     NOTE: The F2 prompt indicates that the keyboard has initialized. This prompt can appear very quickly, so you must watch for it to display, and then press . If you press before you are prompted, this keystroke will be lost. If you wait too long and the operating system logo appears, continue to wait until you see the Microsoft® Windows® desktop. Then, shut down your computer (see Turning Off Your Computer) and try again.

    System Setup Screens

    The system setup screen displays current or changeable configuration information for your computer. Information on the screen is divided into three areas: the options list, active options field, and key functions.

    Menu — Appears on top of the System Setup window. This field provides a menu to access to the System Setup options. Press <¬ >and<® >keys to navigate. As a Menu option is highlighted, the Options List, lists the options that define the hardware installed on you computer.

    Options List — Appears on the left side of the System Setup window. The field lists features that define the configuration of your computer, including installed hardware, power conservation, and security features.
    Scroll up and down the list with the up- and down-arrow keys. As an option is highlighted, the Options Field displays the option's current and available settings.

    Options Field — Appears on the right side of Options List and contains information about each option listed in the Options List. In this field you can view information about your computer and make changes to your current settings. Press to make changes to your current settings. Press to return to the Options List.

    NOTE: Not all settings listed in the Options Field are changeable.

    Help — Appears on the right side of the System Setup window and contains help information about the option selected in Options List.

    Key Functions — Appears below the Options Field and lists keys and their functions within the active system setup field.

    System Setup Options

     NOTE: Depending on your computer and installed devices, the items listed in this section may appear, or may not appear exactly as listed.

    Main

    System Date

    Displays current date settings, in the mm:dd:yy format.

    System Time

    Displays current time settings, in the in the hh:mm:ss format.

    SATA0

    Displays the SATA drive integrated on SATA0.

    SATA1

    Displays the SATA drive integrated on SATA1.

    SATA2

    SATA Port not present.

    SATA3

    SATA Port not present.

    SATA4

    Displays the SATA drive integrated on SATA4.

    SATA5

    Displays the SATA drive integrated on SATA5.

    System Info

    Lists the BIOS version, system name, asset tag, and service tag.

    Memory Info

    Indicates amount of installed memory, memory speed, channel mode (dual or single), and type of memory installed.

    Advanced

    CPU type

    Indicates the type of CPU installed.

    L2 Cache

    Indicates the amount of CPU L2 cache.

    Advanced Chipset Features

    Indicates amount of video memory (32 MB by default).

    Integrated Peripherals

    Allows you to enable or disable the integrated devices and ports on your system.

    CPU Configuration

    Allows you to enable or disable the CPU features that enhance the performance of the system.

    USB Configuration

    Allows you to enable or disable the USB controller.

    Power

    Power Management Setup

     

    ACPI Suspend Type

    Specifies the ACPI suspend type. The default is S3.

    Remote Wake Up

    This option turns on the computer when a user tries to access the computer through the LAN.

    Auto Power On

    Enables you to set an alarm to turn on the computer automatically.

    Auto Power On Date

    Enables you to set the date to turn on the computer automatically (0 by default).

    Auto Power On Time

    Enables you to set the time to turn on the computer automatically (0:00:00 by default).

    AC Recovery

    Off; On; Last (Off by default).

    Boot

     

    Boot Device Priority

    Sets the boot device sequence. Only the bootable devices that are connected to the computer are listed as options.

    Removable Device Priority

    Sets the boot priority among the attached removable devices.

    Hard Disk Boot Priority

    Sets the hard drive boot priority. The items displayed are dynamically updated according to the hard drives detected.

    CD/DVD Boot Priority

    Sets the CD/DVD drive boot priority. The items displayed are dynamically updated according to the hard drives detected.

    Boot Settings Configuration

    Configure Fast Boot, Numlock and Keyboard errors.

    Security

    Provides options to enable, disable or change the passwords.

    Exit

     

    Exit Options

    Provides options to Exit Saving Changes, Exit Discarding Changes, Load Setup Default, and Discard Changes.

  • BeyondBeige

    15 Posts

    871

    0

    Posted November 23rd, 2011 07:00

    BIOS logs are a nice idea, but none available!  As hinted at above, BIOS is very basic.

    In this case the "therm-bar" is just a graphical progress indicator on Dell's boot-time splash screen - nothing to do with temperatures (old-time term I picked up years ago when I used to code - sorry for any confusion caused).

    The closest thing to throttling in the BIOS is SpeedStep, which can be either on or off.  Set either way makes no difference to the beep code. As the beep-code occurs at boot-time (including cold boot), is throttling likely to have kicked in to the extent that it causes a POST error?

    No evidence of overheating problems in the Windows logs.

  • speedstep

    11 Legend

    •

    46969 Posts

    261

    0

    Posted November 23rd, 2011 09:00

    In the old days with computers with Vacuum Tubes Space bar told the CPU to bypass Ram Test and therefore speeded up the boot process.