UNSOLVED

johe

updated

21 years ago

J

johe

1 Rookie

•

22 Posts

0

25021

January 10th, 2006 12:00

A07 BIOS boot problem

I recently upgraded to Bios A07 from A04 and am having a boot problem.  From a cold boot, no drives are found and I must reboot, sometimes several times, before it finds my RAID boot volume.  If I enter the setup screen, I notice that no drives are found (external, DVD or floppy) and the boot sequence has changed and my USB external drive (used for back-up only) is the primary boot source with the RAID volume is the 3rd priority.  Interestingly enough, if I enter the "boot sequence" path (F12) when rebooting, all drives are found and are in proper sequence.  Using this procedure during a cold boot will not work and I have to reboot.
 
Any suggestions would be greatly appreciated.
 
Dell Dimension XPS
3.6 P4 Processor
2gb ram
500 gb HD (2-250 HD in RAID 0)
Maxtor 100 GB USB external HD
DVD R/RW
3-1/2 Floppy
  • Majestic

    2 Intern

    •

    9371 Posts

    1970

    0

    Posted January 10th, 2006 12:00

    After a BIOS update it is not uncommon for the newly installed BIOS to have a conflict with the hardware information stored in the NVRAM.  This can result in hardware detection problems during boot up.  On your system you should be able to clear the NVRAM from with-in the BIOS Setup by following this procedure.....
    • Reboot system and enter the BIOS Setup by pressing F2.
    • Turn on Caps Lock, Scroll Lock and  Num Lock.
    • Press ALT + E then ALT + F (should hear beep) then ALT + B

    Once the NVRAM is cleared the system will redetect all the installed hardware and it should resolve any boot up problems related to hardware detection.

    Message Edited by Majestic on 01-10-2006 08:13 AM

  • 1970

    0

    Posted January 10th, 2006 14:00

    if your system s bios is a tree bios with a blue background, the you cannot clear nvram with alt+E.there is no option for clearing nvram in all tree bioses in dell system. only alt+f works in those systems with tree bios for resetting factory defaults.
    you will have to clear nvram only by using the rtcrst jumper on the motherboard.its sad that dell engineering group removed that option in tre bios systems starting with dim4700 onwards.
    try the jumper option and if it still does not work. then downgrade your bios nad re-upgrade it.i have seen that working on a few  dell systems at a service centre.however there would be a risk of the raid volume getting tampered at times alhough technically it should not but it has happened on a dimension 8400 system.
  • Naoned

    35 Posts

    1970

    0

    Posted January 12th, 2006 14:00

    Hello

    In the bios , select USB not bootable , because it is probable your PC boot in the USB > Hard Drive .

    In the bios A07 you have 3 selection for USB device , select not bootable

    Best Regards

    Naones

  • johe

    1 Rookie

    •

    22 Posts

    1970

    0

    Posted January 15th, 2006 15:00

    Well the problem is the bios cannot find any of my drives, including the USB, CD or Hard Drives.  I notice that if I reboot using cntrl-alt-del when this occurs, I get the "NTLDR not found".  When I do a power off reboot and enter setup, the bios shows an "IDE hard disk" as the primary boot device (which I do not have) with the CD drive as the secondary.  My SATA RAID configuration is listed as the last priority.  So evidently, the bios is changing the boot sequence when it cannot find the Raid drives.  I will try to eliminate all drives, except the RAID drives and CD drives from the boot menu and see what happens.
  • johe

    1 Rookie

    •

    22 Posts

    1970

    0

    Posted January 15th, 2006 15:00

    Having just gone through 2 hard drive failures within the past year, I am somewhat hesitant to attempt anything that would jeopardize my hard drives again.  While I have everything back-up, loading all those programs again is not my idea of computer fun.  I might try regressing to an older bios and then re-flashing the A07 bios again, however.

     

    Resetting the NVRAM appeared to work but the problem came back within a couple of days.  While it doesn't keep the computer down, it is a frustrating experience and I am also trying to deal with a problem with the Blue Screen of Death appearing everytime I insert a blank writeable CD/DVD into one of my writeable drives.  While the latter is more than likely a driver problem, it, too, has become a hassle to correct and I really haven't been able to determine the cause.

     

    Thanks for the help from all who have answered.  I truly appreciate your efforts.

  • Majestic

    2 Intern

    •

    9371 Posts

    1970

    0

    Posted January 16th, 2006 12:00

    JoHe, if clearing the NVRAM temporarily fixed the problem then consider running the Dell Diagnostics on the entire system including the drives.  Possibly a hardware component is failing such as a drive which is causing the drive detection problem at boot up.  When the NVRAM is cleared the problem is corrected until the piece of hardware acts up again.