UNSOLVED

ccmsi

updated

23 years ago

C

ccmsi

17 Posts

0

7700

May 30th, 2003 01:00

8250 running very sluggish right out of the box. Hard Drive seem slow

I just got a new 8250 with 512 Meg Ram, ATI Radeon 9700 Pro, ST360015A 60 Gig HD, DVD burner, etc.   Before this I had an 8100 with 256 Meg Ram, Nvidea video, etc which my son has now. 

Right after I got the machine i noticed that it wasn't snappy. It thinks a few seconds before explorer pops up, outlook express takes about 15 seconds to load and the hard drive seems to crank a lot.  I have applied most tips like turning off services (index, etc), unloading things out of the start up and registry, updating virus, defrag and it has gotten a little better but my old 8100 still out performs it. 

I have a benchmark program I downloaded and everything looks fast except my hard drive.  My hard drive here shows I'm reading and writing about 12 Meg/sec while my 8100  (western digital 40 meg) is getting about 24 Meg/sec.  This 8250 has a Segate hard drive which is 7200 rpms. The whole system should scream.  Drive is formated ntfs which should be optimum.

Games seem to play fine though. I can play Americas Army, Unreal,etc and it performs fine once the games are loaded.

Curious if anyone else is having a similar problem

Thanks

Bill

  • 569

    0

    Posted May 31st, 2003 01:00

    Had the same problem - I bought an identical HDD and an adaptec RAID controller from Dell and my sluggish PC is now fast. Cost about 160.00. Easy to install and setup.

     

    8250 > 2.4g > 256 RDRAM > 2 120gb westerndigital HDD with adapted raid > ATI 9700TX

     

  • andfor

    5 Posts

    569

    0

    Posted May 31st, 2003 04:00

    Check My Computer > Properties > Hardware > Device Manager > IDE ATA/ATAPI Controllers > Primary/Secondary IDE Channel > Advanced Settings -> Current Transfer Mode. What modes are currently in use? It should be Ultra DMA Mode 5 for peak performance. Make sure that "DMA if available" is selected.

    I have two 7200RPM IDE disks on the primary channel (Ultra DMA Mode 5 both) and CD/DVD on secondary (Ultra DMA Mode 2 both). Using DiskSpeed32 I get between 45-50MB/sec read speed on both disks. Please try it and post your results.
  • ccmsi

    17 Posts

    569

    0

    Posted May 31st, 2003 13:00

    andfor, Both Primary and Secondare say they are using Ultra DMA Mode 2.  It is set to use DMA.  Wonder why I'm not at Mode 5. Found this on Dell's web site.  Ran SpeedTest32 and it says I'm averaging about 27 MB/sec though it ran down to about 23Meg/s towards the end.


    Ultra ATA DMA Mode 0 16.6 MB/sec
    Ultra ATA DMA Mode 1 25 MB/sec
    Ultra ATA DMA Mode 2 33.3 MB/sec
    Ultra ATA DMA Mode 3 44.4 MB/sec
    Ultra ATA DMA Mode 4 66.6 MB/sec
    Ultra ATA DMA Mode 5 100 MB/sec

    My Hard Drive

    Model ST360015A
    60 Gig
    7200 rpm
    Suppose to have a 9ms average seek time but I don't think I'm gettign that.
    Interface is Ultra ATA/100

    iamchumley, I have been thinking of trying the western digital 10,000 rpm drive. Do you think I will need a new controller as well for that?  Are you mirroring or something?

    (both of ya) Thanks for answering

  • msrk

    312 Posts

    571

    0

    Posted May 31st, 2003 15:00

    Download and apply this http://downloadfinder.intel.com/scripts-df/Product_Filter.asp?ProductID=663 it will put you in DMA mode 5.
  • ccmsi

    17 Posts

    571

    0

    Posted May 31st, 2003 15:00

    I don't have that hot fix. I just have the following:

    Q329390
    Q329834
    Q322011
    Q328310
    Q329170
    Q329441
    Q331953
    Q810577
    Q810565
    Q810833
    Q814033
    Q814995

    Thanks

  • msrk

    312 Posts

    571

    0

    Posted May 31st, 2003 15:00

     Check in add/remove programs and ensure you don't have hotfix (Q811493) installed. If so remove it.
  • ccmsi

    17 Posts

    571

    0

    Posted May 31st, 2003 16:00

    That didn't seem to change anything. Same read speeds and I couldn't see the DMA of the properties of the controller either to see if it was using dma mode 5.
  • msrk

    312 Posts

    571

    0

    Posted May 31st, 2003 16:00

    It won't be there. Open the application accelerator itself under programs and under primary channel click on Master. On the right side this will bring up the parameters of the hard disk. In the listing will be "Current Transfer Mode", to the right of that will give you the current DMA mode.
  • msrk

    312 Posts

    259

    0

    Posted May 31st, 2003 16:00

    Right below Current Transfer Mode is a little wrench and it says "Transfer Mode Limit". What is to the right of that? post back. The UDMA-2 on your Opticals is fine.

    Message Edited by msrk on 05-31-2003 12:36 PM

  • ccmsi

    17 Posts

    259

    0

    Posted May 31st, 2003 16:00

    It says No Limit. Here is the report.

    Intel(R) Application Accelerator, 2.3.0.2160
         Saturday, May 31, 2003 12:37:32 PM (Local)
         Saturday, May 31, 2003 5:37:32 PM (GMT)

         Operating System
              Windows XP (Build 5.1.2600, Service Pack 1)

         Platform Information
              Processor Type: Intel(R) Pentium(R) 4 Processor
              Processor level: Family 15
              Processor Revision: Model 2 Stepping 7
              Active Processor Mask: 3
              Number of Processors: 2

         Controller Information
              IDE Controller:  Intel(R) 82801BA Ultra ATA Controller, ICH2
              Storage Kit Build(s):  2.3.0.2164,
              Storage Kit Installed:  2.3.0.2164
              Driver Build:  Intel Application Accelerator Driver
              Driver Version:  2.3.0.2160
              IDE Controller Tri-State:  IDE Controller enabled
              PIO Mode Support:  0 - 2 - 3 - 4
              DMA SW Mode Support:  2
              DMA MW Mode Support:  1 - 2
              UDMA Mode Support:  0 - 1 - 2 - 3 - 4 - 5
              Disk Timeout Value:  Default
              CDROM Timeout Value:  Default
              CD Audio Timeout Value:  Default
              UDMA on 80 conductor cable only:  Default, Disabled
              Flush Enable:  Default, Disabled
              Ping Pong Enable:  Enabled

         Channel Information
              Primary Channel
                   No Data
              Secondary Channel
                   No Data

         Device Information
              Primary Master:  ST360015A
                   Model:  ST360015A
                   Firmware:  3.33
                   Device Type:  ATA - Fixed
                   PIO Mode Support:  0 - 1 - 2 - 3 - 4
                   DMA SW Mode Support:  No Support
                   DMA MW Mode Support:  0 - 1 - 2
                   UDMA Mode Support:  0 - 1 - 2 - 3 - 4 - 5
                   LBA (28-bit maximum):  0x06FCCF30
                   LBA (48-bit maximum):  0x000006FCCF30
                   CHS:  3FFF x 0010 x 003F
                   CHS Sectors:  0x00FBFC10
                   Disk Size (28-bit maximum):  55.9 GB (60,022,480,896 bytes)
                   Disk Size:  55 GB (60,022,480,896 bytes)
                   Default Transfer Mode:  UDMA-2
                   Current Transfer Mode:  UDMA-2
                   Transfer Mode Limit:  No Limit
                   Cable Type (Device):  40 Conductor
                   Cable Type (Host):  40 Conductor
                   PIO PPE:  Enabled
                   UDMA Control Register:  Ultra DMA Mode Enabled
                   UDMA Timing Register:  CT = 2 CLK / RP = 4 CLK
                   Base Clock:  Ultra DMA 33 Timings
                   Auto-Acoustic Management:  Minimum Acoustic Output
                   Dynamic APM on AC:  Feature not supported by device.
                   Dynamic APM on Battery:  Feature not supported by device.