tried to add a second drive to my E5570 and it didn't work! It has an internal 2242 WWAN slot with B key that should support a 2242 SATA (not mSATA not NVM) SSD. Got a Kingshark SSD that is M+B slot and specified as SATA SSD but the drive is not recognized, neither by BIOS (all SATA ports are enabled in BIOS, it has sata-0, sata-1, e-sata and pcie-m2 sata knobs switched on!), nor by Linux (no sda device showing up).
Now the drive is working perfectly in external 2242 SATA to USB3 enclosure. I'm sure the enclosure is SATA (B key) and the SSD is SATA. So the problem is not SSD by itself. Somehow the slot in E5570 is not recognizing it. However it should, other users reported success for example here:
Best bet is to ask which drive model the author of the post found did work. Since running an SSD in the WWAN card slot is an unsupported configuration, it may well depend on the specific drive used.
tested the same Kingshark drive in my another Dell E5550 (this one is from 2012) and same finding: drive not showing up in BIOS, not in Linux (no sdX device found). All SATA ports checked on in BIOS, AHCI mode. As it should be but not working. Drive lits up a red (power?) LED when in the slot.
I have no other laptops to test.
I actually need it in my E5570 which is still pretty decent (from 2016 iirc). The BIOS in E5570 shows four drives options:
[ v ] SATA-0
[ v ] SATA-1
[ v ] SATA-2
[ v ] m.2 PCIe SSD-0
to be clicked on or off. (all enabled)
There is a M2 slot in the 2.5" bay (I use actually a hdd drive there) and it is under the 2.5" drive, cant see it completely but there is a M2 socket for sure. that I assume is the PCIe SSD mentioned by BIOS. (ps there is no m.2 SSD with PCIe but with B key to fit the WWAN slot! such stuff doesn't exist). SATA0 should be the regular 2.5 bay which is used by HDD (via cable going to the motherboard). So then we still have the SATA1 and then the SATA2, which per my understanding one of them would be the connection in the WWAN 2242 slot? Or what else? So why is the drive not working? Not enough power provided by the slot? SATA 6G vs SATA 3G incompatibility maybe? SATA not routed in the WWAN slot?
Actually a B keyed M2 slot should provide SATA and USB interfaces. That's what the spec is saying. These SSDs are anyway keyed B+M, so you could also put them potentially into a M keyed M2 slot. M keyed slots provide PCIex4, USB and SATA as per spec. Thus a B+M keyed drive should also be OK in a M keyed slot (it is just to prevent you putting B stuff into M key eg a NVM SSD which requires PCIe). As per my understanding....
ps. the enclosure where the Kingshark SSD works is this here:
no won't boot from M2, however this is not an issue of finding or not finding the drive, it might just not be in the available boot options with that BIOS. In any case it needs to be found first and show up in the system info drives list.
The only thing relevant to my problem I could find about the m.2 spec are the config_0...3 pins:
they have to be wired correctly on the SSD. Measuring the pins I see it is all correct. config_0...3 are all pulled against GND on the SSD, which should signal the motherboard that SATA interface should be exposed. However something doesn't work here.... *headscratch*
nyc10036
6 Operator
•
5640 Posts
5994
0
Posted September 30th, 2020 09:00
Are you wanting to use it as boot device?