UNSOLVED

alexrubbish

updated

9 years ago

Closed

0

6754

March 26th, 2018 14:00

Inspiron 5570 windows installed in HDD not in SSD

Hey Guys, 

I receintly purchased a Dell Inspiron 5570. it came with 1TB HDD + 128 SSD.

I learned that this is not a hybrid drive, so, being separated I tought that Windows should come installed in the SSD, but this is not the case. I get both drives available in the list of discs but the SSD is empty and the C drive is the HDD.

Have any of you had any experience with such situation? I can't think of an explanation of why the system is installed in the hdd and not in the ssd.

thanks for your support.

cheers

This conversation is no longer open for comments or replies and is no longer visible to community members.

  • Saltgrass

    6 Operator

    •

    4328 Posts

    •

    15932 Points

    6655

    1

    Posted March 26th, 2018 15:00

    If you look at Disk Management, is the full (or almost full) SSD space available?

    Putting an OS on a small drive like that, especially with the way Win 10 does updates is just asking for trouble. 

    If the drive was being used for something other than just empty storage space, it would be nice to know.

  • jphughan

    11 Legend

    •

    13985 Posts

    •

    79931 Points

    6652

    2

    Posted March 26th, 2018 15:00

    I've seen reports of this occurring elsewhere.  It is definitely NOT supposed to ship that way.  Some systems ship with a 32GB SSD that is meant to serve as a cache module for the HDD, but if you have a 128GB SSD, it should be set up as a fully independent drive and should definitely have the OS on it.  To Saltgrass's point, 128GB is a bit small by today's standards, so you may want to make sure most of your applications are installed on the spinning disk rather than the SSD, but you'll still be able to fit some applications on there because Windows by itself would not grow to fill a 128GB SSD on its own.  Even with Windows 10 and its "new release every 6 months" cycle, you wouldn't use up that much space because Windows has built-in routines to clean up files to facilitate rolling back updates and even full release upgrades as needed.  Windows 7 did NOT have those routines, so that became a problem after many years of updates in environments where the C drive was sized relatively small.

    In terms of fixing it, if you're comfortable performing a clean installation of Windows, it would be fairly straightforward to wipe the existing spinning disk, then install Windows onto the SSD and finally partition the spinning disk as desired for how you will want to use it.  Alternatively, you could probably just clone your existing HDD installation to the SSD using a tool like Macrium Reflect Free.  You'd just want to make sure your system booted from the SSD afterward rather than the HDD.  You should be able to tell pretty easily based on how quickly Windows loads, but the size of the C drive would also clue you in since Windows always assigns "C" to the partition it actually booted from, and since your SSD and HDD are very different sizes, that's easy.

  • 6629

    0

    Posted March 27th, 2018 07:00

    Thanks for your reply jphughan,

    Yeah I thought about cloning the drive, I might try that. I just wanted to know if there was a reason why it was shipped this way, because I thought it was really weird.

    I really appreciate your support. =)

     

  • 6632

    0

    Posted March 27th, 2018 07:00

    thanks for your reply Saltgrass! 

    The laptop is new, it shipped with both drives and the SSD is empty.

    I have an old Dell Latitude 5520 and I installed an 128GB SSD and I works but I am constantly run the disk space liberator tool to delete the update files. But it does work.

    but it's just weird that a computer would come with an ssd as a secondary drive.

  • Ivy li

    15 Posts

    6594

    0

    Posted April 1st, 2018 19:00

    if you want to install the operating system on the SSD drive, you can use a disk cloning software like AOMEI Backupper to clone only os to SSD or clone entire hard drive. 

  • vinceay

    1 Message

    5434

    0

    Posted August 28th, 2018 08:00

    Is there a way to get it to boot in UEFI Secure Boot mode from the SSD? I cannot get it to boot from the SSD without switching to the legacy boot mode.

  • Mascall

    1 Message

    4741

    0

    Posted October 25th, 2018 07:00

    Did you ever solve this problem. I have the same issue!

  • 4725

    0

    Posted October 25th, 2018 11:00

    Hey Mascall, 

    as a matter of fact I just solved this issue. I had to copy my files to an external hdd because I was using about 300GB of my 1TB hdd, so I had to get under 100GB considering the SDD my computer had was a 128GB SDD

    So after I deleted my documents and some programs, I cloned the hard disk with ease us and replaced the boot priority to have the computer start with the ssd instead of the hdd.

    After I booted, I checked my C disk was 128GB and not the 1TB drive, so after ensuring I was on the SDD I formated the 1TB drive with diskpart. and assigned it a new letter (I choosed F but that's up to you) And after that I replaced the location of the documents folder to the F drive so my programs are on my C drive and my files are on my F drive.

    Hope this could serve of any help, but in case you wanna try, it. 

    Oh and about the windows activation, the system activated itself without me doing anything.

  • jphughan

    11 Legend

    •

    13985 Posts

    •

    79931 Points

    3806

    0

    Posted October 25th, 2018 11:00


    @vinceay wrote:

    Is there a way to get it to boot in UEFI Secure Boot mode from the SSD? I cannot get it to boot from the SSD without switching to the legacy boot mode.


    If you can only boot in Legacy mode, then you didn't run the clone properly.  Booting in UEFI Secure Boot mode requires that your disk be set up as GPT, including the necessary FAT32 EFI partitions.  If you only cloned the OS partition and/or your SSD uses the MBR partition layout, it will only be bootable via Legacy mode.  I personally use Macrium Reflect Free for cloning, and I've found that if you want to solve a problem like this, the best method is to clone to the new disk, physically remove the old disk (only temporarily if you want to keep using it later), then try to boot the system.  If it fails, boot your system from the Rescue Media that Reflect helps you create and run the "Fix Boot Problems" function.  If your system boots at that point, you should then be able to reconnect the original disk, then use something like diskpart to completely wipe all of its partitions (including the hidden partitions) and set up a single partition to turn it into a data-only disk.

  • F4WSO

    1 Rookie

    •

    1 Message

    1723

    0

    Posted November 25th, 2018 16:00

    Same issue here. I'm glad I'm not alone! Dell support was not helpful.

    Can I just swap out the spinning drive with a new SSD, SATA III (2.5 inches), or are there other specs to consider?