ast1234

updated

2 years ago

A

ast1234

1 Rookie

•

7 Posts

1

19615

April 2nd, 2018 09:00

Inspiron 3455, upgrade HDD to SSD

I have a Dell Inspiron 3455 system and would like to replace my slow HDD with a new SSD.  I purchased a Crucial MX500 SSD and have attempted to clone using multiple cloning software (Acronis, Macrium, EaseUS) as well as trying a fresh install of Windows 10.  Unfortunately, I cannot get the computer to boot into Windows no matter what I try (secure boot off, MBR and GPT formats, etc).  I have exhaustively searched these and other message boards, but I have not been able to fix my problem.  Anyone run into this before and/or have any thoughts on what could be preventing it from booting?

  • zebo007

    1 Rookie

    •

    1 Message

    10545

    1

    Posted January 20th, 2020 23:00

    After reading all these posts and with some trial and error, I was finally able to successfully install the Samsung EVO 860 1TB HD into this Inspiron 3455.

    1. Upgraded the BIOS to the latest version 4.3.0

    2. Turned off Secure Boot

    3. Switched to Legacy Mode

    4. Created a new USB with Windows 10 using Rufus. Set partition scheme to MBR and under Advanced drive options check to add support for old BIOS.

    5. Set boot priority USB first then SSD.

    6. Computer booted straight into USB and was able to install and boot into Windows successfully.

  • Tesla1856

    10 Wizard

    •

    18086 Posts

    •

    71947 Points

    9211

    0

    Posted April 2nd, 2018 10:00

    Try setting BIOS to UEFI, AHCI, and maybe leave SecureBoot off (for now, during initial install).

    Does this SATA SSD appear in BIOS and at correct size? That is the first step.

    Clean install Windows-10/64bit to completely blank SSD (raw, no partitions). If having problems, you might want to try disconnecting all other drives (the other spinning HDD and SATA-SSD) for now.

    If using Macrium Reflect, I image to a file first with verify on.

    Dell Rockstar

    Microsoft Windows and Apple iOS Developer (Retired)
    - Like many of you, I can appreciate a good game-engine.
    - I answer questions here, but I'm not a Dell employee.
    - Consider giving posts you like a "thumbs-up"
    - Posting models-numbers and software versions speeds trouble-shooting.
    - Click "Mark as Accepted Answer" on any post that answers your question best.

  • ast1234

    1 Rookie

    •

    7 Posts

    9209

    0

    Posted April 2nd, 2018 10:00

    Thank you.  In my attempts, I have tried with UEFI, AHCI, and secure boot off.  

    The SSD does appear in BIOS and at the correct size (500 GB).

    I used command prompt to clean the SSD and then attempted to install Windows from a USB.  I used Rufus to create the bootable USB, and it appears to install Windows correctly, but then it won't boot.  For the Windows 10 file, I have actually tried all combinations of GPT/MBR and FAT32/NFTS.

  • Philip_Yip

    11 Legend

    •

    16052 Posts

    •

    65915 Points

    9207

    1

    Posted April 2nd, 2018 10:00

    What Windows 10 Version are you using Version 1709?

    Where do you get in the installation process (UEFI Boot with Secure Boot, SATA Operation AHCI)? Do you get to the Region, Keyboard and Network Screens?

    http://dellwindowsreinstallationguide.com/clean-installing-windows-10-rs2version-1703creators-update-with-uefi-and-secure-boot/

     

  • Tesla1856

    10 Wizard

    •

    18086 Posts

    •

    71947 Points

    7227

    1

    Posted April 2nd, 2018 11:00


    @ast1234wrote:

    1. Thank you.  In my attempts, I have tried with UEFI, AHCI, and secure boot off.  

    2. The SSD does appear in BIOS and at the correct size (500 GB).

    3. I used command prompt to clean the SSD and then attempted to install Windows from a USB.

    4. I used Rufus to create the bootable USB, and it appears to install Windows correctly,

    5. but then it won't boot. 

    6. For the Windows 10 file, I have actually tried all combinations of GPT/MBR and FAT32/NFTS.


    1. Good. Yes, that should work. Also, a reminder ... after you get it booting and working, DO NOT install Intel-RST (just use Microsoft bundled drivers).

    2. Good

    3. With DiskPart, right?

    4. Never heard of using Rufus for this part. You just press F12, and boot the Windows-10 flash-drive you created with Media Creation Tool.

    5. So, I assume the Windows Installer can see the blank SSD and lets you select it (as un-partitioned space) for the Install Destination. Are you sure you only have the SSD connected?

    6. You want GPT and NTFS, but the Windows Installer takes care of all that.

    Dell Rockstar

    Microsoft Windows and Apple iOS Developer (Retired)
    - Like many of you, I can appreciate a good game-engine.
    - I answer questions here, but I'm not a Dell employee.
    - Consider giving posts you like a "thumbs-up"
    - Posting models-numbers and software versions speeds trouble-shooting.
    - Click "Mark as Accepted Answer" on any post that answers your question best.

  • ast1234

    1 Rookie

    •

    7 Posts

    9197

    0

    Posted April 2nd, 2018 13:00

    @Philip_Yip, thank you.  I am using the version that is available from the Media Creation Tool.  I'm not sure which version it is.

    From your link, I get through Part 3.  When the computer restarts, that is when it gets frozen at the boot screen (which looks like the first picture under "Booting from the Bootable USB in UEFI").  So I do not get to the region, keyboard, network screens.

  • ast1234

    1 Rookie

    •

    7 Posts

    7222

    0

    Posted April 2nd, 2018 13:00

    @Tesla1856  Thank you. 

    3. Yes with diskpart -> select disk -> clean.  Then I confirm in disk management that it is actually clean.

    4. I burned the ISO to the USB with Rufus rather than the Windows Media Creation Tool.  I previously attempted to use Media Creation Tool but couldn't even get it to boot up, and after reading some other suggestions, tried Rufus which at least let me get to and partly through setup.

    5.  SSD and the USB with the Windows 10 ISO are connected, although I have also tried removing the USB to see if that was the hang up.

  • Tesla1856

    10 Wizard

    •

    18086 Posts

    •

    71947 Points

    7215

    0

    Posted April 2nd, 2018 14:00


    @ast1234wrote:

    @Tesla1856  Thank you. 

    3. Yes with diskpart -> select disk -> clean. 

    3b. Then I confirm in disk management that it is actually clean.

    4. I burned the ISO to the USB with Rufus rather than the Windows Media Creation Tool.  I previously attempted to use Media Creation Tool but couldn't even get it to boot up, and after reading some other suggestions, tried Rufus which at least let me get to and partly through setup.

    5.  SSD and the USB with the Windows 10 ISO are connected, although I have also tried removing the USB to see if that was the hang up.


    3. Right. You can check your work (before and after) inside DiskPart with "List Disk".

    3b. Not sure how you are running Disk Management on a blank computer. Try using DiskPart from PE in Macrium Reflect's Bootable Rescue Disk. The SSD should NOT be initialized with Disk Management before installing Windows fresh. The Installer takes care of all that.

    4. No, no Rufus. If you can't press F12 and "one time boot" the "perfectly created" Windows flash drive, you have some other problem.

    5. Of the actual "fixed disks" ... just the SSD (no spinning HDDs, etc.). Yeah, obviously the Windows flash drive has to be inserted. F12 on machine boot to start it.

    Dell Rockstar

    Microsoft Windows and Apple iOS Developer (Retired)
    - Like many of you, I can appreciate a good game-engine.
    - I answer questions here, but I'm not a Dell employee.
    - Consider giving posts you like a "thumbs-up"
    - Posting models-numbers and software versions speeds trouble-shooting.
    - Click "Mark as Accepted Answer" on any post that answers your question best.

  • Philip_Yip

    11 Legend

    •

    16052 Posts

    •

    65915 Points

    9178

    0

    Posted April 3rd, 2018 06:00

    Do you have anything in the USB ports apart from the Bootable USB?

    Have you tried using a different USB (although I don't think it is the USB at this stage)?

    Do you know what BIOS revision your system has?

    Have you ran the [F12] preboot diagnostics?

  • ast1234

    1 Rookie

    •

    7 Posts

    9159

    0

    Posted April 4th, 2018 07:00

    @Philip_Yip, thank you again.

    1. My mouse and keyboard are both attached as USB devices.

    2. No, I only have one USB large enough to fit the ISO.

    3. 4.3.0 (from Dell, dated 10/8/2016)

    4. Yes, no problems ever found.