UNSOLVED

MacAddict1

updated

19 years ago

M

MacAddict1

29 Posts

0

8619

September 13th, 2007 21:00

Snapshots in AX150

Hello all, I have setup a CLARiiON AX150 DP with 12 750GB hard drives. I created a Disk Pool with 11 of them (kept 1 as a hot spare). It gave me about 6750GB of space. Then I created a Virtual Disk with 6500GB leaving 250GB aside as I was planning on using it for a daily snapshot. From what I've been reading, I was supposed to set 20% of the Virtual Disk aside to create the Snapshot? One doc said that the max had to be 20% but nothing that I have come across says anything about the minimum required. Will I be OK to setup a snapshot with the 250GB space left? Thanks
  • Dev Mgr

    6 Operator

    •

    9308 Posts

    •

    3 Points

    391

    0

    Posted September 14th, 2007 11:00

    The snapcache is used to store the blocks of data that have changed compared to the time when the snapshot was started.

    If the changes on your source lun (virtual disk) are less than 250GB during the time that you're running the snapshot session (when you're running your backup), the 250GB should be sufficient. Navisphere (EMC) recommends 20% as that's what is the average that EMC has probably seen to be needed/used. With Express it automatically wants to do 20%, but less may work if your data is not too dynamic.

    Keep in mind that the snapshot has to be given to a server other than the one that has the source lun. It would need to be able to read the filesystem, so a similar OS is needed (Windows family, Linux family, ESX, etc).
  • MacAddict1

    29 Posts

    391

    0

    Posted September 14th, 2007 12:00

    Dev Mgr, Thanks. Our changes are about 30 GB per 24 hours so I should be OK. I was just afraid that when I go to set it up in Navisphere express, it would not let me create it. And yes, it will be mapped to the backup server instead of the live server.
  • MacAddict1

    29 Posts

    391

    0

    Posted September 14th, 2007 18:00

    That's no good. Why does it require 20%? My 3TB share only has about 30GB of changes a day...
  • Dell-Jeff G

    156 Posts

    391

    0

    Posted September 14th, 2007 18:00

    The initial cache LUN will be 20% of the source LUN, in increments of 10GB.
    If you don't have free space 20% of the source LUN the snapshot creation will fail.
  • Dell-Jeff G

    156 Posts

    391

    0

    Posted September 19th, 2007 13:00

    The 20% was used to make the solution easier to implement. 
    If a smaller number was used, and not enough space was reserved to "grow the cache on the fly" then the snapshots would fail. 
    20% initial cache size doesn't fit everyone's use case and I have messaged this information to EMC.   Maybe a future version of FLARE will offer lower initial cache LUN size. 
     
  • MacAddict1

    29 Posts

    391

    0

    Posted September 19th, 2007 14:00

    Jeff G, It did allow me to create a snapshot with the 250GB left in the system. MacAddict
  • Dev Mgr

    6 Operator

    •

    9308 Posts

    •

    3 Points

    391

    0

    Posted September 20th, 2007 11:00

    The step in Navisphere is one part, but not a guarantee that the 'whole thing' will work.

    Verify with the Navisphere server utility that you can start the snapshot (session) and then with the backup server that you can 'allow access' to the snapshot.

    I would think that if it allows you to prepare the lun for a snapshot in NaviExpress that it'll allow starting the session just fine (Navisphere Manager will let you do this).