I have a Dell 16 Plus DB16250 with a Intel(R) Wi-Fi 7 BE201 320MHz Wi-Fi card and running windows 11 home 26h2 the router is config for WAP 3 but the laptop shows WPA2-Personal
I have changed the router to WAP 3 Personal and the laptop uses WAP 3 but the problem is then I loose my television and phones so I have had to change back to WPA3-Personal-Compatibility.
I will now close this as I am unable to change the TV but I now know my laptop will work.
Your laptop almost certainly does support WPA3—the Intel BE201 supports WPA3-Personal on Windows 11 with a current Intel driver. The important point is that netsh wlan show drivers only lists what the driver supports; it does not show which security mode the current Wi-Fi connection is using.
Check the live connection
Run this in Terminal or Command Prompt:
netsh wlan show interfaces
Look for:text
Authentication: WPA3-Personal
If it says WPA2-Personal, Windows connected using WPA2. If it says WPA2/WPA3-Personal or similar, the router is likely broadcasting a mixed/transition-mode network, and Windows may select WPA2.
Microsoft notes that when both WPA2 and WPA3 are offered, Windows will normally try WPA3 first, but the router’s advertised security mode and the saved profile still matter.
Fix it on the router
In your router’s Wi-Fi settings, look for the security mode for the 2.4 GHz and 5 GHz SSIDs you are connecting to. Set it to:
WPA3-Personal only
or, depending on the router UI:
WPA3-SAE WPA3 Only WPA3-Personal (SAE)
Avoid these if you want to force WPA3:
WPA2/WPA3-Personal
WPA3-Personal transition mode
WPA2-Personal + WPA3-Personal
Those mixed modes allow WPA2 clients, so Windows may show or use WPA2. WPA3-Personal uses SAE; WPA2-Personal uses PSK.
Refresh the saved Wi-Fi profile
Windows may retain the old WPA2 profile. Forget and reconnect:
Open Settings → Network & internet → Wi-Fi → Manage known networks.
Select your SSID and choose Forget.
Reconnect and enter the password again.
Verify with:
netsh wlan show interfaces
If it still shows WPA2, temporarily set the router to WPA3-only, forget/reconnect, and test again.
Install the latest Intel Wi-Fi driver—preferably from Dell’s support page for the DB16250 using its Service Tag, or directly from Intel for the BE201. Intel states WPA3-Personal requires driver version 21.10.x or later, while WPA3-Enterprise requires 21.90.3.x or later; a current Wi-Fi 7 driver should be far newer than that.
After updating:
netsh wlan show drivers
Confirm these lines include WPA3:
Authentication and cipher supported in infrastructure mode: WPA3-Personal
I changed the router to WAP 3 Personal from WPA3-Personal-Compatibility and that fixed my laptop but I then lost my other connection i.e. TV & Phone so I have had to re set the router back to WPA3-Personal-Compatibility
I have latest Intel driver installed 24.70.0.3 and the latest verion of windows 26H2
Under Authentication, it should now show WPA3-Personal. If it fails to connect, the router is still advertising WPA2 compatibility or its WPA3 implementation is not accepting the client; recheck that the SSID is set to WPA3-Personal/SAE only.
If it still shows WPA2
Update the Intel Wi-Fi driver from Intel/Dell Support Assist rather than relying only on Windows Update.
Disable Random hardware addresses for that Wi-Fi network in Settings > Network & internet > Wi-Fi.
Forget the network again, reboot, then import the XML profile.
Test on the 5 GHz SSID first; some routers implement WPA3-only differently on 2.4 GHz.
Confirm the router’s setting is WPA3-Personal, not merely “WPA3 capable” or “WPA2/WPA3”.
Canadaleigh
1 Rookie
•
6 Posts
•
34 Points
7
0
Posted October 21st, 2026 09:24
Hi All
Thanks for all your responses and help.
I have changed the router to WAP 3 Personal and the laptop uses WAP 3 but the problem is then I loose my television and phones so I have had to change back to WPA3-Personal-Compatibility.
I will now close this as I am unable to change the TV but I now know my laptop will work.
Thanks to all for the advice given
Leigh