
UNSOLVED
Closed
Area 51 R2, No Boot
Hello, I am really hoping to get some insight on what is going on here. Long story short, I got a Alienware Area 51 R2 on a trade. The PC came with no hard drives. I have several laying around so I grabbed one with Windows 10 on it and powered it up. Hard drive light shows activity for roughly 5-6 seconds then goes off and stays off. No display on monitor. All fans work, keyboard lights up as it should as well as the mouse. So power is getting to everything. The dual GTX 970’s also light up and appear to be working.
Does the computer require any special files to boot?
I have replaced the CMOS battery as it had a dollar tree battery installed, also cleared cmos via pins.
Removed both GPU’s and replaced with working spare. Still no video signal.
Tried booting with blank HHD via USB Bootable, still nothing.
Hopefully I’m missing something stupid simple. Thanks in advance!!
Responses (12)
Solutions (0)
ProfessorW00d
6 Operator
•
2373 Posts
•
10247 Points
389
0
Posted January 14th, 2023 07:00
I'm pretty sure the Windows Operating System is keyed to a specific motherboard . . . so you can't just throw in another hard drive. You will have to purchase a new Windows software and key.
A working computer should be able to Post, show-BIOS options. Most Dell/Alienware can even run ePSA Diagnostics .
Try F12 on-boot. A working Area51-R2 should be able to boot the following flash-drives ... Microsoft Windows-10 Installer, Macrium Rescue, and Ubuntu Linux .
Dell Rockstar
Microsoft Windows and Apple iOS Developer (Retired)
- Like many of you, I can appreciate a good game-engine.
- I answer questions here, but I'm not a Dell employee.
- Consider giving posts you like a "thumbs-up"
- Posting models-numbers and software versions speeds trouble-shooting.
- Click "Mark as Accepted Answer" on any post that answers your question best.ProfessorW00d
6 Operator
•
2373 Posts
•
10247 Points
374
0
Posted January 14th, 2023 21:00
From my Area-51 R5 experience, if there is a single 3rd party fan installed, the system will boot into an infinite loop of diagnostic fail, with constant black screen on the monitor. I had to add 3 OEM Nidec fans with Y-splitter adapter cables to get a successful POST.
You seem to have a no video no POST situation. When you trade for it did the previous owner demo it was working right before switching ownership? If they just claimed it was all working without you verifying that could be a problem.
In a no POST situation try remove all memory and all connected storage devices and all peripheral devices such as usb keyboard etc. Install only one ram in dimm 1, use a very simple video card that was verified working on another pc to test.
R2 board has a proprietary 8 pin gpu power connector socket at lower right corner. confirm Dell psu is plugged in that socket. not sure board would post without this connected even when you are using a low power gpu.
Honestly that part of the trade was just icing on the cake on my end so I was not too worried about it but I really like how it looks and now I want to use it.
I’ll check for that plug at the bottom, I have removed all GPU’s and tested with working card. Still nothing.
So I have tried everything mentioned, I still have been unsuccessful in getting it to work. I found something on Dell about holding the power for 30 seconds to reset the clock. I will be trying that today but wanted some more feedback on possible things to do. Thanks to everyone who has reached out so far on trying to help me!
ProfessorW00d
6 Operator
•
2373 Posts
•
10247 Points
43
0
Posted January 21st, 2023 06:00
Just a note that if the "working card" you tested with is not OEM Dell you may have to disable Secure Boot in BIOS to get functionality. I realize you cannot currently get into BIOS at this time, just adding some information to your testing regime.

Udbassist
1 Rookie
•
7 Posts
387
0
Posted January 14th, 2023 07:00
Figured there was some kind of a catch. I’ll look into that! Thank you.