That link was invalid and What I did try are listed here:
Method 1
Start your computer with the floppy disk drive in place, and with the startup disk in the drive. When asked if you want to start with CD-ROM support, select Start the computer WITHOUT CD-ROM support.
You will eventually see the following prompt:
A:\>
(Above that, you should see a line reading "The diagnostic tools were successfully loaded to drive X:". Throughout these instructions, replace X: with the drive letter specified by this line.)
At the A:\> prompt, type:
format c: /s [press enter]
This command will take a moment to complete, and at the end it will ask you to specify a disk label. Enter an 11-character name or simply press Enter.
Once you are back at the A:\ prompt, type:
copy oakcd*.sys c: [press enter]
When the A:\ prompt appears again, type:
X: [enter] (Make sure that you type in the letter specified in the ......successfully loaded to drive X: line)
You should now see an X:\ (or whatever) prompt. type:
copy mscdex.exe c: [enter]
Type edit [enter]. This will open the text editor in DOS. Type the following line:
c:\mscdex /d:mscd001
Press Alt-f and select Save As... . Name this file c:\autoexec.bat .
Press Alt-f again, and select New.
Type the following line:
DEVICE = C:\oakcdrom.sys /d:mscd001
Press Alt-f and select Save As... . Name this file c:\config.sys .
Turn off the laptop, insert the CD-ROM drive, and restart. The computer will come back up with the A:\ (or possibly C:\ ) prompt as before. Now, type D: and press enter.
Put the Windows CD in the CD-ROM drive, at the D:\> prompt, type setup then press enter. This should start Windows Setup.
_________________________________________________________________________________
Method 2 Tried using this bootdisk http://www.compu-docs.com/DeskBoot.htm
__________________________________________________________________________________
Method 3 Lets have the original 98 boot floppy back in the drive.
1.Start your computer with the floppy disk drive in place, and with the startup disk in the drive. When asked if you want to start with CD-ROM support, select Start the computer without CD-ROM support.
2. You will eventually see the following prompt:
A:\
Above that, you should see a line reading "The diagnostic tools were successfully loaded to drive X:". Throughout this document, replace X: with the drive letter specified by this line. At this prompt, enter:
format c: /s
3. This command will take a moment to complete, and at the end it will ask you to specify a disk label. Enter an 11-character name or simply press Enter.
4. Once you are back at the A:\ prompt, enter:
copy oakcd*.sys c:
5. When the A:\ prompt appears again, enter:
X:
6. You should now see an X:\ prompt. Enter:
copy mscdex.exe c:
7. Enter edit . This will open the text editor in DOS. Enter the following line:
c:\mscdex /d:mscd001
8. Press Alt-f and select Save As... . Name this file c:\autoexec.bat .
9. Press Alt-f again, and select New.
10. Type the following line:
DEVICE = C:\oakcdrom.sys /d:mscd001
11. Press Alt-f and select Save As... . Name this file c:\config.sys .
12. Turn off the laptop, insert the CD-ROM drive, and restart. The computer will come back up with the A:\ prompt as before. Now, enter D: .
13. Put the Windows CD in the CD-ROM drive, then enter Setup . This should start Windows Setup.
Method 4 # Insert the Windows 98 CD into the CD-ROM drive.
NOTE: If the Windows 98 window appears, click to close the window.
# Insert your setup boot floppy disk into the floppy drive.
NOTE: For more information about creating a setup boot disk, refer to Dell Knowledge Base Article: FA1014475.
# Reboot your computer.
# At the MS-DOS® prompt, type the following commands and press the key after each command:
x: (where x indicates the letter of your CD-ROM drive)
cd win98
setup
A prompt to start Scandisk appears.
# Press the key.
# When Scandisk has finished checking the hard drive, press the key.
The Welcome to Windows 98 Setup window appears.
# Press the key.
The Microsoft Windows 98 Setup Wizard window appears.
_________________________________________________________________________________
The conventional way of loading 98 onto a desktop which I may have done 100 times or more comes back with the command "Connot be run in dos mode" when I type setup from the A:\> prompt
Any help here is greatly appreciated to restore this new found nightlight.
Message Edited by Googlebot on 01-21-2005 08:08 AM
I repaired the link in my original post. It's not clear whether you have a retail Windows 98 CD or a Dell Recovery CD for Windows 98. The link covers either option.
Denny Denham
2 Intern
•
18798 Posts
181
0
Posted January 21st, 2005 04:00
Since you didn't elaborate on what specifically was tried, I'll offer the generic instructions here.
Message Edited by Denny Denham on 01-21-2005 09:10 AM