Aurora R8, not connecting to #2 S2417DG most restarts
Hi All,
This issue is nothing new and has plagued me since I got the machine. After ordering the R8 I picked up two matching Dell S2417DG g-sync monitors (1440p). There have been no upgrades made to the machine.
Specs: i7-9700k; 16GB RAM; RTX 2080 Super; 1TB NVME; liquid cooling. Both monitors connected to RTX 2080s display port ports.
Nearly every time I boot the computer it ignores one of the monitors. I'll get the no signal message and then the monitor goes back to sleep. It happens to both, but typically it is the one I will refer to as my "main". Rarely the "other" one won't get a signal. In either case (or the very rare case where both don't work) I power the monitor off and back on, then it'll work as intended.
Things I have tried: swapping cables, and trying the remaining ports on the 2080s; in Windows display settings the monitor will be greyed out, re-selecting to extend the displays gives a "setting cannot be saved" message; also tried figuring out if I could do the same thing in Nvidia control panel, but no luck there either. The only thing that seems to help is turning the monitors off and back on.
I've scoped out the Nvidia forums as well, saw others with complaints and/or mixed results. Some blame Windows 10 but didn't find anything that helped. I keep Nvidia drivers up to date, Alienware Update installs system updates too. Also tried to update drivers for monitors but most recent update on Dell site is years old, though installing that tricked me into thinking it was fine for a day or two.
In addition, I avoid letting the R8 go to sleep ever if I can help it. Usually upon waking, it's extra difficult to get the monitors to come back on. Same as above, playing with power buttons on the monitors. This is fairly similar to another unsolved post I saw on here.
Lastly, I want to blame the monitors but unfortunately I can't. My Lenovo work laptop, which barely has enough horsepower to check accuweather before locking up, shockingly runs both just fine at 1400p. Also in the couple years I've been using them with both systems they haven't acted up for the Lenovo. Only difference is the laptop uses 1 USB-C to HDMI and 1 regular HDMI for the other. R8 is on Display Port as stated above so I only have to switch inputs on the monitors. I'm out of ideas on what to try, it's not the end of the world it's just incredibly annoying. Anyone else deal with this or have any ideas?
If anyone else is having this issue I believe I have some steps that helped me in mostly resolving this issue.
I finally found the power saver option in the monitors and disabled it. It doesn't seem to be much different than "normal" mode since the monitors still shut off after maybe 30 seconds or so.
I also bought new cables, just to rule them out, but they didn't seem to make any difference.
I moved the "extra" monitor to the DP for the Intel Integrated graphics (wanted to see if I could squeeze more FPS in games on the main one).
Installed Intel's driver assist tool, however I DID NOT install the drivers (this seemed to remedy the one being stuck off).
I think the Power Saver option was the big one. Now when the second monitor isn't working, holding the Win+Ctrl+Shift+B for a few seconds wakes up the "dead" monitor.
Edited To Add Note: Now it seems like the monitors usually both come on. It seems like the one that is now connected to the integrated graphics only "dies" when I'm using a tool before windows loads that can't seem to detect the second monitor. IE: fiddling with the bios, running chkdsk, etc. Once I'm booted back into Windows holding the shortcut above wakes the second monitor.
So hopefully this helps someone else with a similar setup.
TWO Dell S2417DG monitors (@ 1440p) . Both via DisplayPort ports.
I have tried: swapping cables, and trying the remaining ports on the 2080s;
My Lenovo work laptop, shockingly runs both just fine at 1400p. Only difference is the laptop uses 1 USB-C to HDMI and 1 regular HDMI for the other.
Well, typically, DisplayPort is preferred. However, the problem does seem to be following them (either the Nvidia-card, the cables, or the DP ports on the monitors).
These cables ... did they come from Dell with the monitors ? Are they "straight-thru", thick gauge, and not too long ?
Can you lock the monitors to DP-Input, or do you have to leave on Auto-Detect?
Dell Rockstar
Microsoft Windows and Apple iOS Developer (Retired) - Like many of you, I can appreciate a good game-engine. - I answer questions here, but I'm not a Dell employee. - Consider giving posts you like a "thumbs-up" - Posting models-numbers and software versions speeds trouble-shooting. - Click "Mark as Accepted Answer" on any post that answers your question best.
I appreciate the response. It's hard to troubleshoot when it's been going on so long. Thinking back I don't know if it acted like this immediately. I keep thinking it was after an update, but it could have been Alienware Update, Windows, GEForce Experience update. After posting I was poking around for "windows 10 dual monitor issues". It seems like a fairly common issue. I tried the CTRL+SHIFT+WIN+B shortcut but unfortunately it didn't help.
Bouncing back to "These cables..." I don't remember if/what cables the monitors came with, if they came with DP cables though I wouldn't have purchased extra. If by straight-thru you mean standard DP male connector on both ends, no adapters, then yes, they are straight-thru, thick gauge, and length-wise they're just long enough to reach the back of the PC, no more than 3-5 foot I'd guess.
I never found an autodetect option, so I've always used the menu on the monitors to switch between HDMI/DP.
In any case I ordered some new VESA certified DP 1.4 cables and will try those when they arrive.
Mike KC
9 Posts
498
0
Posted August 14th, 2022 08:00
If anyone else is having this issue I believe I have some steps that helped me in mostly resolving this issue.
So hopefully this helps someone else with a similar setup.