UNSOLVED

philipkoo2

updated

18 years ago

P

philipkoo2

41 Posts

0

24527

September 7th, 2008 08:00

Ways of reducing noise in PE 1750?

Got myself a PE 1750 (Nice by the way Dell, though I bought it from eBay, so maybe thats why I have no problems?...moving on.). It was going to go in a closet, next to where I sleep. The problem? It makes too much noise! I've heard of more quiet fans, just not sure what or where I can get those.

 

I also noticed that the fans located near the power supply units and one in the back, next to the power socket makes the most noise. Should I just disconnect them, or leave only one on? Will that affect system reliability or performance? If so, which one? Does the servers even make enough heat to become a problem with the fans being off?

  • Dev Mgr

    6 Operator

    •

    9308 Posts

    •

    3 Points

    813

    0

    Posted September 7th, 2008 22:00

    Disconnecting fans may cause your system to overheat and shut down (and possibly cause permanent damage). As it's a server, you generally cannot use generic replacement parts either for the chassis pieces as manufacturers (like Dell) tend to use fans that are made to just fit into the spot where they are supposed to go and they may also need specific wiring to account for the motherboard to read the fanspeed.
  • philipkoo2

    41 Posts

    813

    0

    Posted September 8th, 2008 03:00

    Dang. I am not too worried about overheating. I'm more worried about using the server...
  • Dev Mgr

    6 Operator

    •

    9308 Posts

    •

    3 Points

    813

    0

    Posted September 8th, 2008 13:00

    Put it in a closet and close the door. That how I run my self-built NAS box (6 harddrives in a system with decent cooling fans make more noise than I want in my computer room at home).
  • philipkoo2

    41 Posts

    813

    0

    Posted September 9th, 2008 00:00

    Crud. The closet, while helps reduce the noise, it isn't reduced much. At this point, I am willing to go with using other fans. Where can I find the specs for the fans used by the PE 1750? I've been told that Dell's fan plug is just unique, and splicing the plug onto another fan would work and will not affect the system, so I'll go and try that.
  • pcmeiners

    6 Operator

    •

    1771 Posts

    813

    0

    Posted September 9th, 2008 12:00

    If you keep it in the bedroom, best to consider it white noise and a radiator..... 

     

    Impractical but I have replaced fans in server with quieter units BUT finding them can be tedious, as they must be the same size, have the same  wiring (speed sensor), may or may not have the correct connector which would require sniping and a soldering gun or purchasing separate connectors . Fan units have to have same voltage and running speed rating but lower decibel rating (the lower DB rating, the more expensive). Lastly, even though you could purchase the same spec fans, except for DB rating, it likely grounds for not covering the server warranty. Disconnect any fan and the server will likely balk, no less go into melt down.

     

    One electronics suppler.....

     

    http://www.digikey.com/?WT.term=digikey&WT.campaign=1048&WT.content=text&WT.medium=cpc&WT.source=google&cshift_ck=921509516cs501693903&WT.srch=1

  • philipkoo2

    41 Posts

    813

    0

    Posted September 9th, 2008 23:00

    Digi-Key doesn't have one in the exact size (or so I believe: Doesn't look like they have 40x50x38MM), which one did you get for yours?
    Message Edited by philipkoo2 on 09-09-2008 05:56 PM
  • 813

    0

    Posted September 14th, 2008 14:00

    hello!

     

    i have the poweredge 1400sc..an old  but nice one

     

    he did make a lot a noise too..two fans screaming like a jumbo-yet

     

    but now he is really quiet without the notorius :fan failure strike f1/f2

     

    what did i do?

     

    i took off the red and the black wire-pins out of the fan-connector (he has three :red black and blue)

    and left the blue one where he was (in the fan-conector)

     

    then i attached the red and the black fan-wires to a hard disk (mylex) connection

    the fans runs now at 5 or 7 volt instead of 12 volts and no post error messages!

     

    it is a onorthodox solution but it works great!!

     

    i dont how old your PE is but i bought mine for 15 euro (with no memory) and of course out of warranty

    he runs fine at 2x 1 ghz 1gb compaq memory!

     

    good luck  

     

     

    Message Edited by frankie_toonboom on 09-14-2008 10:36 AM
    Message Edited by frankie_toonboom on 09-14-2008 01:29 PM
  • philipkoo2

    41 Posts

    813

    0

    Posted September 14th, 2008 15:00

    frankie_toonboom,

     

    sadly, my poweredge uses 68p scsi for hard disc, there goes my poweredge, too noisy for productive use...

     

    Very funny with your server being a person :), maybe treating mine like one too might help...

  • 813

    0

    Posted September 14th, 2008 16:00

    well

     

    mine is 68pins scsi equipped as well but i mean the powersupply  connectors..from the ATX power supply

     

    to the cd-roms and the disc- drives..

     

    these connections  have 4 wires:

     

    2x black 1 red and 1 yellow

     

    i put the red and the black fan-wires into the red and black connectors from the power supply

     

     

     

     

  • philipkoo2

    41 Posts

    160

    0

    Posted September 15th, 2008 22:00

    PE 1750's drives get power from the motherboard. Any ideas on where I can get a power supply that has an output of 5 volts?