UNSOLVED

Mshgaw

updated

19 years ago

M

Mshgaw

10 Posts

0

9021

February 21st, 2008 21:00

How on earth do I do this

okay. i am extremely frustrated. i want to reformat my computer with the disk seeing as I no longer am able to use the Ctrl+F11 thing like I used to.  So how do I go about reformatting with the XP disk i was given when it was shipped to me.
 I tried BOOTING from CD but didn't work
I am so frustrated I need help
  • keithg2

    2 Intern

    •

    935 Posts

    221

    0

    Posted February 21st, 2008 22:00

    What model Dell do you have?

    Do you have RAID on in your system setup?

    Did you press F12 when you rebooted so you could choose your CDROM drive to boot from?

     

    If RAID is enabled in the system setup, you will need to load the SATA/RAID drivers from a floppy disk during the XP install. You will need to download the Intel or nVidia drivers from the SATA section of the Drivers & Download page for your model. During the XP install, you will see a message at the bottom to press F6 to load 3rd party scsi or raid drivers. If you're not using RAID, disable it in your system setup by setting RAID Autodetect/ATA (XPS 400 & 410) or IDE (Inspiron 530s).

     

    During the XP install when you select the partition you want to install it on, you can delete the C partition, then create a new C partition and format it before the XP installation continues.

    Message Edited by keithg2 on 02-21-2008 05:42 PM
  • keithg2

    2 Intern

    •

    935 Posts

    221

    0

    Posted February 21st, 2008 22:00

    I couldn't find an Inspiron 520 in the list of Manuals are you sure it's not a Dimension E520?

     

    If you could find  your manual and look in the System Setup section, you'll find if your system has RAID capability. The Dimension E520 does have RAID capability under Drives / SATA Operation. If you do have the E520, go in to system setup (F2) at boot up and set the Drives / SATA Operation to RAID Autodetect/ATA so you don't have to load the drivers during XP install.

     

    When you selected to boot from your CD, the XP CD should have shown a message like "Press any key to boot from CD....". You have like 5 seconds to press any key so it continues to boot.

  • Mshgaw

    10 Posts

    221

    0

    Posted February 21st, 2008 22:00

    I have Dell Inspiron 520.
    I don't know how to tell if I have that RAID thing
    I even pushed F12 to highlight and select BOOT from CD

    I dont have a floppy disk drive
  • keithg2

    2 Intern

    •

    935 Posts

    221

    0

    Posted February 21st, 2008 23:00

    Ok good.

    Then in your system setup under SATA mode, make sure it says IDE save and EXIT setup.

    Try booting again from your XP install CD.

     

    EDITED: I didn't read your last post. If the CD is not being detected for you to boot from make sure you're trying to boot from the Dell XP CD. Maybe try another bootable CD to see if it's the CD media causing the issue. Otherwise, I'm not sure what to tell you.

    Message Edited by keithg2 on 02-21-2008 06:11 PM
  • Mshgaw

    10 Posts

    221

    0

    Posted February 21st, 2008 23:00

    I apologize Its a Inspiron 530
    Spelling error I apologize
  • Mshgaw

    10 Posts

    221

    0

    Posted February 21st, 2008 23:00

    Yeah but the thing is. There is no where that says Press any key to boot If i did that i woul know where to do what to do. I even changed the boot sequence and nothing helped. I had a Dell person come and Replace my CPU this morning and he did everything correctly and placed everything back in place. i ruled out the CD itself cuz I can access the Recovery CD from my desktop but I can't boot it to reformat
  • shesagordie

    12 Elder

    •

    46017 Posts

    221

    0

    Posted February 21st, 2008 23:00

    Mshgaw

    See if Dell's reinstallation guide here, can help.

    If you have two optical drives installed, try using the other drive.

    Bev.


    ===================================================
    Please don't send me questions about your system by DCF Messenger.
    Post the issue in the appropriate Board, where they will be answered.