i have also had the same issue.
this happens every time i try to discover windows hosts.
i have tried discovering with ip and fqdn.

it works fine with idrac and cmc for me, discovered by ip range

Thanks for the questions guys.

We have a support matrix published off of the DTC page that might help with the list of supported devices in this first release.

Just to get things started, let's make sure it can discover your iDRACs correctly.  So if you go through the default path on the discovery wizard it should take you to the basic WSMan discovery where you can enter the IP addresses or range for your Servers/iDRACs.

This release does not have much support for in-band discovery like OM Essentials did.  With that product, you could discover SNMP+OMSA or WMI+OMSA.  Not so for Enterprise--it's more iDRAC (out-of-band or agent free) focused.

There is some basic SSH / Linux support, but the inventory is less compared with iDRAC/WSMan.  There are some notes in the user guide / help I believe that could get you some in-band Windows discovery. But the setup on the end-node is burdensome.  

For storage in this release, our support is limited to Compellent and we're evaluating interest in other storage products.  So I'll definitely pass along the interest in MD.

Hope this info helps.

Rob

To clarify, are you saying this product ONLY actually works with DRAC and not OMSA?  If so, it's pretty much belly up for us, and I'm hard pressed to understand how this could be the case as it guts the product.  I had zero success in discovering my servers, and now it seems the reason may be that it can't?  For a product that's already a year overdue based on browser tech discontinuation, this is not encouraging.

Hi there,

Yes, that is correct.  The product focus is mainly on iDRAC discovery although there is some ability to discover in-band Windows or in-band Linux/SSH.

I'll make sure I pass along your feedback on the h/w support level to the right folks.  I'm assuming you are looking for support for pre-12G PowerEdge models, correct?

Thanks,

Rob

Hello,

I've installed Dell OpenManage Enterprise yesterday. I can find and discover server via iDRAC discovery on the same subnet that OME but when a started discovery on other subnet i've the same error like other guys.

I've OpenManage Essential that run successfully on all iDRAC from all server of my compagny.

...

thanks for your help...

I can discover R510 fine but R710 and R910 get instantly failed when trying to discover. 

All the devices have the same v2.90 iDRAC firmware and are on the same subnet.

Any ideas?

Hi @jcappelle

Ok, just to be clear, can you specify what model of PowerEdge server you are trying to discover?

In OM Essentials, we supported both SNMP and WSMan discovery of an iDRAC.  For Enterprise, we are supporting only WSMan discovery of the iDRAC.

The different subnet should be ok.  Did you put those in the same discovery task or a separate task?  I wouldn't think it would matter, but for the purposes of troubleshooting, maybe create a new disc task and enter a known IP from that subnet just to check.  And be sure to use just WSMan default settings.

You might try using the Dell Troubleshooting tool to double check the connection to one of the iDRACS.  It kind of depends on your environment as to if that tool will be useful (it's Windows based, etc.).  But in some cases it can help if you run the WSMan test.

Thanks,

Rob

Hi @MLaanem

Thanks for the post.  As you point out, if the networking and f/w is set up the same on the 710/910, you should be good to go.  I'm assuming you are using the default settings for the disc wizard (just WSMan only).

Sometimes, for debugging, it is helpful to create a new discovery task with just a single IP for one of the 710/910 servers.

Can you see if the troubleshooting tool can run a successful WSMan test to connect to one of the 710/910?

Thanks,

Rob

Hi @DELL-Rob C and thank you for your quick reply

I have tried a single IP discovery and subnet discovery. Its the same result both ways. 

Troubleshooting tool WSMAN test is successful.

error message is: 

Also i noticed that all the R510 have Express licences but R710 and R910 have Enterprise licences. Maybe the issue is with iDRAC licences?