UNSOLVED

dramacydal

updated

19 years ago

D

dramacydal

18 Posts

0

13867

January 25th, 2008 20:00

NEED HELP *URGENT*

ok long story short, my master harddrive has a virus (virtumonde i believe) which is almost impossible to remove ive done everything i could and i just cant get rid of this virus and its messed up my computer so bad that the internet wont even work(tried restarting pc, restarting modem etc... wont work), so as a last resort im trying to make my slave drive master because its clean..virus free but i cant seem to make it master. ive tried swapping cables from my master drive to the slave but the computer wont even boot if the slave drive is connected... please help.


Message Edited by dramacydal on 01-25-2008 04:55 PM

Message Edited by dramacydal on 01-25-2008 04:55 PM

Message Edited by dramacydal on 01-25-2008 06:49 PM
  • TomXPS

    1310 Posts

    161

    0

    Posted January 25th, 2008 21:00

    I do not think you have much luck booting off the other drive since the hardware may have been totally diferent than you have on you 8400.  But the easiest way is just to swap the two drives.
     
    There is an free utility that will retrive the product key.  I did a search in Googles and found the following a few here a couple I found.
     
     
     
     
     
    The google search I used was:
    Microsoft Product Key Util
     
    If you have the DELL OEM disk you should not need the product key.  Also it should be on a sticker attached to you PC.  At least the OEM version that was shipped with your system.
     
     
     
     
     
     
     
  • shesagordie

    12 Elder

    •

    46017 Posts

    161

    0

    Posted January 25th, 2008 21:00

    dramacydal

    What is the computer model and version of windows?

    Does the Slave Drive have a copy of windows installed?

    Bev.


    ===================================================
    Please don't send me questions about your system by DCF Messenger.
    Post the issue in the appropriate Board, where they will be answered.
  • dramacydal

    18 Posts

    161

    0

    Posted January 25th, 2008 21:00

    its a dell dimension 8400 and im on windows xp. btw i just tried to reinstall windows on my master harddrive but i could not find the 25 letter serial key... so is there anything i can do? how can i switch my slave to master? and yes the slave has windows xp installed i took it out of my moms computer a while back and put it in this one as slave  but cant remember how i did it or how to switch it to master...
  • dramacydal

    18 Posts

    161

    0

    Posted January 25th, 2008 22:00

    thanks for that but now i have a new problem... when i try it reinstall windows xp i get a error "setup was unable to read or write to drive c. if a virus scanner is running, disable it then restart setup" i disabled every AV i have and its still doing this... im so frustrated NOTHING is working today.
     
    Edit: both HD's came out of a 8400, it must be somthing im doing wrong but i dont know what.


    Message Edited by dramacydal on 01-25-2008 06:06 PM
  • shesagordie

    12 Elder

    •

    46017 Posts

    161

    0

    Posted January 25th, 2008 22:00

    dramacydal

    You should find the product key on the COA label attached to the left side of the case.

    But with a Dell reinstallation disc, the product key usually is not requested during the installation.

    See here.

    Unless your mother's computer is a Dimension 8400, similar to yours, I doubt that the hard drive will work in your 8400.

    Did you try using Dell's PC Restore by Symantec utility that's factory installed on the D-8400 hard drive to revert the system back to it's factory condition?

    Bev.


    ===================================================
    Please don't send me questions about your system by DCF Messenger.
    Post the issue in the appropriate Board, where they will be answered.