UNSOLVED

chiggins01

updated

8 years ago

C

chiggins01

1 Rookie

•

8 Posts

•

29 Points

0

1729

February 11th, 2019 05:00

Cant build R640 with Win2012R2 using WDS

Struggling to build a R640 with Win2012R2 using WDS. Have tried the following...

1) Raid/Nic from dell download site

2) OS deployment drivers from Dell download site

3) Can build via Lifecycle controller and OS disk, so took drivers into WDS but still fails. (don't see what the difference could be)

4) and many others

Have successfully built to Win2016 but need Win2012R2 also. Seems to be a driver issue but just will not build.

When rebooting after putting OS onto disk get the following.

R640Fail.jpg

 

  • Daniel My

    12 Elder

    •

    6204 Posts

    1590

    0

    Posted February 11th, 2019 09:00

    Hello

    My first guess would be USB 3 drivers. I can't recall if USB 3 is enabled by default on the R640, but I don't think the 2012R2 installation environment has USB3 support. Check the BIOS to see if USB3 is enabled. If it is enabled then disable it until the OS is installed. You can find documentation about BIOS settings in the manual on the system support page.

    http://www.dell.com/support/

    Thanks

  • chiggins01

    1 Rookie

    •

    8 Posts

    •

    29 Points

    1576

    0

    Posted February 12th, 2019 01:00

    Hi, thanks for the reply.

    The Bios appears to have been simplified, there is no USB3 mentioned, just options for disabling front/back/internal and DRAC. 

    Apart from that , I have just caught a previous error screen, you know the ones that flash up for a split second. It says

    inaccessible boot device.

    So it seems it is a driver issue even though I have tried the drivers used during a lifecycle build, downloaded the OS Deployment drivers and downloaded standalone drivers for the megasas. Strangely the first part of the WDS build is WinPE (win10) which sees that disks, its just when it then tries to boot to Windows 2012R2

  • Daniel My

    12 Elder

    •

    6204 Posts

    1544

    0

    Posted February 13th, 2019 08:00

    With that error I would suspect the driver causing the problem is the storage controller. I don't know what storage controller you are using. I suspect you have RAID enabled in the BIOS, which turns on the S140 RAID controller. That is the only controller I can think of that 2012R2 would not support with native drivers.

    If the OS is installing successfully and only erroring after first boot then I would disconnect the USB device before the boot starts to eliminate issues loading the driver for that storage device.

  • chiggins01

    1 Rookie

    •

    8 Posts

    •

    29 Points

    1527

    0

    Posted February 14th, 2019 05:00

    Our R640s use the H740P Mini controller, while in the BIOS the 'embedded SATA' is set to AHCI mode. When installing from Windows DVD, I have to add the megasas driver to see the disks, all works fine. I have also put the very same drivers in the install.wim file used by WDS but get the same issue. Have also booted the DVD and used the recovery console to check the bcdedit details and all looks ok.
  • Daniel My

    12 Elder

    •

    6204 Posts

    1520

    0

    Posted February 14th, 2019 09:00

    There is an odd issue with a storport driver that could be what you are experience. In the processor settings of the system BIOS disable UPI Prefetch. If this allows the system to boot then run Windows updates and/or install the latest storport driver. Once you are at the latest storport you can re-enable UPI Prefetch and it should not experience the issue.

    If the issue persists then that is not the issue you are experiencing. You will need to continue narrowing down the problem driver. It could still be a storport driver issue even if it is not the exact issue that affects speculative memory fetching.