
UNSOLVED
xps 8500 disc configuration
I ordered an xps 8500 and opted for getting just the 1TByte HDD becasuse I wasn't real happy about the other options. I've been following some of the other posts concerning the number of SATA II and SATA III ports, but have not yet seen a definitive answer on the speed of the mSATA port on the motherboard. If that port is SATA III (6 GB/sec) then I should buy an mSATA III SSD large enough to hold the OS and my APPS, and keep the data on the HDD. On the other hand, if the motherboard port is SATA II, I should buy a SATA III SSD to put in place of the HDD, and move that drive (for data) to a SATA II slot. If i am going to invest in an SSD for the OS and APPS in an effort to increase performance, I want that drive in a 6 GB/sec slot.
Responses (14)
Solutions (0)
I talked with a dell tech rep a couple days ago, and he confirmed to me that the msata port runs at SATA III speeds. Although Dell encourages this motherboard port to be used as a cache, if the ssd installed in the msata is 128 GB or larger, it can be used as a boot device. I'm going to put a 128 GB in the mSATA (at 6GB/sec) for the boot device and use the 1 TB dive in the SATA III slot 0 location (also 6 G/sec) for data. I realize that an HDD cannot sustain 6GB/sec, but with the onboard cache of the disc, there is still an advantage of having it on the SATA III port. I'll let you know how that turns out.
It's great to see that it works. There is so much misleading advice circulating from some Dell agents that I was beginning to wonder if there was something strange about the 8500 that would stop the mSATA being used as a boot drive. Would you care to tell us how you populated the mSATA. Did you clone the old C drive, use the Dell restore disc or do a clean install from a Win7 install disc?
I don't know if you saw my post a while back, but that is what I did. I added a 128 GBmSATA card to the mother board and kept the 1T drive in the SATA 3 slot. I did an install of the system by first creating a system restore disc, doing a clean install to the mSATA, and then installing my apps. The only problem that I had was afteri went to Dell to get and install updated drivers, when i would boot up, I got the error “non-system disc, Press any key to continue”. The system would boot ok, but this was annoying. After a lot of work, I figured out that driver update B765JC4A, a firmware update for the Seagate 1 TB drive was causing the problem. So I re-installed the OS,etc and all the updates, apps, and new drivers EXCEPT for B765JC4A. Problem solved.( There should be no need to run that since the firmware had already been updated anyway). This system is really superb!!
Thanks Dr.Doug for that info.
Just to be clear, to get a fully satisfactory installation you used a Windows 7 SP1 system disc (begged, borrowed or downloaded from the MS sub-contractor site) and the key from the COA on the Dell case.
I bet that took ages and a big slice of your bandwidth in getting the updates. Did you consider using the Windows 7 system repair disc and installing the Win7 image?
Also, you don't need the COA on the Dell case if you order the Dell Reinstallation disk. Plus, use this guide for the clean install as it is tailored to Dell computers:
en.community.dell.com/.../1434.1-1-a-clean-install-of-windows-7-on-dell-systems.aspx

drnex
2 Posts
484
0
Posted June 14th, 2012 18:00
This is the question of the day. I think the mSATA is a III port based on what others have said, but no HDD even reaches the limits of SATA II, so it's better to move the HDD to a Sata II and buy a full-fledged (non mSATA) SSD for SATA III port since they're much cheaper than mSATA. That's what I just did, I am using the 240 GB Sandisk Extreme SSD in the SATA III port and the 1 TB HDD in the SATA II port.