markwragge

updated

18 years ago

M

markwragge

71 Posts

0

1118

August 19th, 2008 11:00

ns20 cannot see new luns after rescan

I have removed some existing luns from the ns20 using the nas_disk -d command to delete them. This appears to have worked successfully. I have then used navisphere to delete the raid group and then create a new raid group with more disks. I have carved up the raid group into 4 * 500gb luns with ID 18-21. I have then added the 4 new luns to the storage group.

When i perfrom a rescan using the Celerra Mgmt GUi the new storage is not picked up. I have tried several times. What commands can I run from the CLI to do the following:
Scan for new hardware/luns.
List out all disks and raid groups that the celerra can see.
Any other useful commands to solve this problem!!

Thanks, Mark
  • nandas

    6 Operator

    •

    1473 Posts

    613

    0

    Posted August 19th, 2008 12:00

    Hi Mark,

    Have you set the Host ID (HLU) of these LUNs to a value greater than 16 while adding them to the Storage Group? The Host ID field is the right most column in the storage group - select LUNs property page.

    You may refer to the following documentation - please note the step 1d.

    http://corpusweb130.corp.emc.com/ns/common/post_install/Config_storage_gatway.htm

    If the HLU is not set accordingly - Celerra will not recognize these newly added LUNs. Please set the HLU and then run rescan on the Celerra Manager.

    Hope this helps,
    Cheers,
    Sandip
  • sagle

    90 Posts

    613

    0

    Posted August 19th, 2008 12:00

    server_devconfig server_x -list -scsi -disks

    will show you all the current disks listed in the nasdb, you can use the probe option to look for new disks available, but not yet created in the nasdb. You can aquire those via

    server_devconfig server_x -create -scsi -disks
  • markwragge

    71 Posts

    613

    0

    Posted August 20th, 2008 01:00

    thanks for this info. the hostID is my problem here as the hostIDs for my luns range from 6-9. I did not understand the difference between LUN ID and Host ID. But now that i know that this is the problem i cannot see how i set the hostID. There does not appear to be an option to set the host ID when I add the lun to the storage group or when i initially create the lun.

    How can i set the host ID for a lun to greater than 16 when adding it to a storage group.

    Also, i could not access the file at the link you sent.

    Thanks again for help so far.
  • dynamox

    11 Legend

    •

    20419 Posts

    •

    87439 Points

    613

    1

    Posted August 20th, 2008 03:00

    right after you add the lun to storage group ...scroll to the far right corner ..there you will see the "HostID" column. Click in that column right next to your LUN and you should get a pull down menu where you get to select HostID.
  • Peter_EMC

    674 Posts

    613

    1

    Posted August 20th, 2008 03:00

    In navisphere manager:.

    Right Click on Celerra Storagegroup under storagegroup, Select Luns ..., Luns Tab, Click the Lun you want to add in the above window "Available LUNs", click on Host ID of this Lun in the "Selected LUNs" Window, there you will be able to select a Host ID aka HLU

    Edited, because dynamox was faster, but I can not delete it:
    Peter
  • nandas

    6 Operator

    •

    1473 Posts

    613

    0

    Posted August 20th, 2008 06:00

    Both you and "dynamox" were much faster than me to reply :) - time zone also helped you ;).

    I am sure Mark has got it by now. If not, please feel free to revert back.

    Cheers,
    Sandip