
UNSOLVED
Closed
XPS 8940, won't boot
I have a little used 2 year old XPS 8940. Over the last several months, it has taken longer and longer to boot to Windows 10. Now it can take a couple of hours, if it even gets there. Once it does boot to Windows, it seems to run fine.
Just to enter the bios through F12 can take an hour, if it gets there. And, to do one of the F12 processes available, can take an hour or more. The Dell diagnostics function says the computer/memory is fine.
When the computer did boot to Windows, I did some troubleshooting like running scandisk and adjusting what opens on startup.
Not sure what to try now?
Thanks in advance.
Responses (13)
Solutions (0)
I don't think this is a BIOS issue. I assume you had the problem even before putting in V2.10.0?
What I think the problem is some h/w errors or timeouts?
I'd suggest opening the case and ensure ALL cards, cables and connections are secure.... including the RAM. All cards and RAM I'd take out and re-insert.
Same goes for cables, especially the ones to the boot drive.
Test again after you do that.
Still a problem, REMOVE any 'extra' h/w attached, and I mean basically anything not need to boot. Yes, it could cause BIOS warnings if you take out a CD/DVD drive for instance.
You did not specify what configuration you have... so the 2 things that I'd look at is the Video Card if you have one (Nvidia or AMD usually), the other being extra RAM you installed if you did?
Either could be causing problems for you.
In the case of you having a DISCRETE (add-in) video card, once you do boot, switch over to the on-board INTEL 750 video on 8940. I think all you should need to do it move the connection from the Monitor to it, not really sure though, there could be a BIOS setting that overrides it? Once you are working from the Intel video, try rebooting and see if that fixes it, but you do have to remove the Discrete card first. If it does, the card could be the problem.
As for RAM, if you added ANY, remove it and try rebooting (BIOS will tell you there was a memory change). Since you never mentioned the RAM size you have, but if it is a single 16GB RAM stick, possible it is the problem, but the F12 testing should catch that?
You can do it other ways to to test RAM, see here --> https://www.sweetwater.com/sweetcare/articles/how-to-test-ram-for-windows-pc/ as it might find some problem. If so, you'd probably need to buy new RAM, "crucial.com" I'd suggest looking at for RAM. If you are working on the 8940, it has a program to suggest what will work for your XPS.
Lastly, what is your CPU? 10th or 11th Gen? Unlocked one? Did you change some parameters if unlocked? RESET it if you did, overclocking could cause problems.

Thank you for your suggestions.
Cables and connection and memory card all connected or seated ok. video card that came with computer was previously removed, so it's just onboard video. no extra ram---just 16 gb stick that dell diagnostics said was ok; i think that i should be able to see size of memory in bios too, but i haven't looked yet.Cpu is 10th, i think, and was never unlocked. only devices attached to computer now are monitor and wired keyboard/mouse. when i last turned on computer, i just get dell splash screen, with dell logo only.........and then nothing more happened, even an hour later. Computer has SSD and a sata hard drive.i still will try updating bios tomorrow. And i will try to find another memory stick. not sure about timing of problem vs. bios update. but slowness did not happen overnight----it's gotten increasingly slow. i thought critical bios updates occurred automatically, but system was not updated to 2.11.Any additional thoughts?Thanks.Off the top of my head, I'm still thinking a h/w problem, and specifically now one of the drives.
I''d try disconnecting the hard drive and boot... but if it IS one of the drives, it most likely would be the SSD.
Actually, I'd test that first... here is a program to test it that you can d/l and try:
https://crystalmark.info/en/software/crystaldiskmark/
Reason it could be the problem, it will slow down boot for sure, and if it presents READ errors or force retried, that is what would happen. Your hard drive is a secondary, that is holds some programs and data while the SSD is the System drive.
One way to test:
https://crystalmark.info/en/software/crystaldiskmark/ and there is Crystal Disk Info as well.
This is my CrystalDiskInfo, and I have a WDC SN530 512GB SSD:
Other ways to test as well, check these links:
https://www.makeuseof.com/ways-test-ssd-speed-performance/
https://www.geckoandfly.com/23934/ssd-hdd-effective-read-write-speed/
https://ssd.userbenchmark.com/Software
That last one above is good as it will show you where you stand against other drives... way low, probably the SSD is failing OR you do not have AHCI set in BIOS but RAID. That will slow it down.
My Crystal Disk Mark on the SSD:
My BIOS is set to AHCI and this SSD is not blazing fast, but if you run that program you should be near it or better. Way off on some, well, check the BIOS for RAID/AHCI and see which is set. DO NOT change it if RAID, but Google or search this forum on how to do it. Do it wrong and you could have booting problems.

Off the top of my head, I'm still thinking a h/w problem, and specifically now one of the drives.
I''d try disconnecting the hard drive and boot... but if it IS one of the drives, it most likely would be the SSD.
Actually, I'd test that first... here is a program to test it that you can d/l and try:
https://crystalmark.info/en/software/crystaldiskmark/
Reason it could be the problem, it will slow down boot for sure, and if it presents READ errors or force retried, that is what would happen. Your hard drive is a secondary, that is holds some programs and data while the SSD is the System drive.
One way to test:
https://crystalmark.info/en/software/crystaldiskmark/ and there is Crystal Disk Info as well.
This is my CrystalDiskInfo, and I have a WDC SN530 512GB SSD:
Other ways to test as well, check these links:
https://www.makeuseof.com/ways-test-ssd-speed-performance/
https://www.geckoandfly.com/23934/ssd-hdd-effective-read-write-speed/
https://ssd.userbenchmark.com/Software
That last one above is good as it will show you where you stand against other drives... way low, probably the SSD is failing OR you do not have AHCI set in BIOS but RAID. That will slow it down.
My Crystal Disk Mark on the SSD:
My BIOS is set to AHCI and this SSD is not blazing fast, but if you run that program you should be near it or better. Way off on some, well, check the BIOS for RAID/AHCI and see which is set. DO NOT change it if RAID, but Google or search this forum on how to do it. Do it wrong and you could have booting problems.

Your hardware---and hard drive---hunch seems correct. SSD was 96% with CrystalMark, but then I noticed that the SATA drive was missing from File Explorer. I then disconnected that drive, and the computer quickly booted. SATA is set for RAID.
The SATA drive has data files and is partitioned.
How should I troubleshoot the SATA drive?
Thank you.
When was last time you replaced the CR2032 motherboard battery? If the battery died, BIOS likely reverted to its default SATA Operation setting, AHCI.
Dell installed Windows with BIOS set to RAID so that could explain things. I'd replace the battery before doing anything further, if nothing else than to rule the battery out for only a few bucks.

ispalten
7 Practitioner
•
2652 Posts
•
9776 Points
485
0
Posted April 23rd, 2023 08:00
OK, glad you discovered the 'root' problem.
Now what to do it the next question!
So, with that in mind, I have to ask:
You can change the setting, see here, for instance, https://www.dell.com/community/XPS-Desktops/XPS-8940-added-HDD-change-to-AHCI/td-p/8112738 but I STRONGLY suggest you MAKE a back-up of the SSD (if still on RAID setting in BIOS). Some times you might lose the drive contents.
Back to the hard drive though, you might not be able to recover anything. Right now, I'd go out and by another drive and put it in. IF you had a back up of the old drive and its partitions, you CAN restore it.
I learned my LESSON a long time ago... I make BACKUP using the 'old' Acronis True Image (I said OLD because they changed to subscriptions and added features I do not need) weekly of ALL drives on my PC and the same on my wife's. Macrium Reflect is another suggested (Free) but that will end soon I recall, but here is a link, https://www.majorgeeks.com/files/details/macrium_reflect_free_edition.html (NOTE: you will need a drive you can put the back up on, so if the existing hard drive can't be recovered to be usable, buy a new one or get a USB External drive).
Assuming you can't access the hard drive at all, I'd suggest Googling "recover a hard drive" and look at the links. There are programs, both free and fee that might work (I guess depending on the reason the drive doesn't work)? However, if the electronic are fried, nothing short of a company that recovers the drive by physically removes the platter(s) and uses tools to read it.
I wish you luck, but it 'sounds' like complete drive failure somehow? If not, could still be a cable or motherboard controller problem (I doubt it) and getting a new drive and it too can't be read/used would point to that (and the cable is the easy fix and power connector too). Assuming it isn't the simple fix, DATA and POWER cable (check those again, disconnect and reconnect, and the data cable from the motherboard as well), no way out but a new drive I guess?
Next thing I'd do, also buy a USB External drive and the 'real' Macrium (or other back up program) and start making backups ROUTINELY. I do it once a week (I can affordup to lose one weeks data loss) but you can do it as often as you wish, and decide on type of back ups. Need to know more or have questions, Private Message me rather than here.