UNSOLVED

Ignacio Candel

updated

6 months ago

IC

Ignacio Candel

1 Rookie

•

2 Posts

•

7 Points

0

293

June 3rd, 2026 10:59

Migrating windows 2019 server Operating system from physical disk to raid1 virtual disk

I have a PowerEdge T150 windows server with 3 physical disks, of which one is a 500 GB SSD, and the other two are 2 1tb HDDs which are combined under the Perc S150 RAID controller to one RAID 1 virtual disk. My boss has recently asked me to switch out the SSD for two other 1TB HDD's and configure these to be another RAID 1 virtual disk, and for the life of me I cannot get this to work. The steps I have followed for this: I boot into the SSD(having already made both HDDs RAID-compatible and having created the RAID1 virtual disk), I clone the entirety of the SSD to the virtual disk with macrorit reflect, I boot into the virtual disk to see that everything works, then I turn off the computer and disconnect the SSD. Up to this point everything is fine, but when I try to boot back into my RAID1 virtual disk the bios utility tells me there are no physical disks associated to it. Plug in the SSD, everything works fine.

Solutions I have tried: Other programs, like clonezilla, all with similar issues. Using a flash usb to rebuild the system. 

Many thanks for any help you can provide, I´m really at my wits end here!

Sincerely,

Ignacio

  • DellMartinS

    Moderator

    •

    3885 Posts

    •

    25816 Points

    0

    0

    Posted June 5th, 2026 12:18

    There are two common causes here:
    The machine is booting in UEFI mode, but the EFI System Partition and its boot files were not properly recreated or registered on the new RAID1 volume. 
    The clone copied Windows, but not the disk/boot identity in a way that the firmware accepts once the source SSD is gone. 
    A plain clone often works for data, but Windows Server boot migrations between different physical disks or controller layouts are much more reliable when you repair boot records after the move or perform a restore into a freshly created target array. 
    Best fix
    The most reliable approach is:
    Create the new RAID1 virtual disk first on the two new 1 TB HDDs.
    Boot from Windows Server installation media or a recovery USB, not from the cloned SSD.
    Use Startup Repair or manually rebuild the boot files for the new RAID volume.
    If needed, reinstall Windows onto the new RAID1 and restore your data/configuration from backup.
    Dell community guidance for similar migrations strongly suggests backing up, creating the RAID volume, and restoring or reinstalling rather than depending on a simple clone from one boot disk to another.
    If you want to try repairing the clone
    If you want to salvage the cloned system instead of reinstalling, do this:
    Leave the SSD disconnected.
    Boot into Windows recovery media.
    Open Command Prompt and inspect the partitions with diskpart.
    Find the Windows partition and the EFI/System partition.
    Rebuild the boot files onto the RAID1 disk with bcdboot, using the Windows folder on the cloned volume.
    Then verify the firmware boot order points to the new RAID virtual disk, not the old SSD.
    For UEFI systems, the key is that the EFI boot partition must exist on the new array and the firmware must have a valid entry for it. Without that, the clone can look fine in Windows but still fail as soon as the original drive disappears. 

    with kind regards Martin/ Liebe Grüße Martin

     

    Did I answer your query? Please click on ‘Mark as Accepted Answer’. ‘Thumbs up’ the posts you like!

     

    DELL-Martin S

    Social Media and Communities Professional

    Dell Technologies | Enterprise Support Services

    #IWork4Dell


  • Ignacio Candel

    1 Rookie

    •

    2 Posts

    •

    7 Points

    0

    0

    Posted June 8th, 2026 09:42

    The issue that I face when I follow the steps outlined in your response is that the option to boot from the new RAID virtual disk disappears from the boot order points as soon as I disconnect the original SSD. Even when rebuilding boot files through a recovery medium, the RAID virtual disk does not show up again.

  • DELL-Joey C

    Moderator

    •

    4170 Posts

    •

    20965 Points

    0

    0

    Posted June 9th, 2026 06:56

    Hi,

     

    I don't think you can do that. The OS partition and bootloader has boot file to load from the SSD.

     

    My opinion is to rebuild the operating system and copy the data over. 

    DELL-Joey C

    Social Media and Communities Professional

    Dell Technologies | Enterprise Support Services

    #IWork4Dell

    Did I answer your query? Please click on ‘Mark as Accepted Answer’ if I did.