
UNSOLVED
W
wackybadger
7 Posts
0
9555
January 9th, 2009 17:00
Setting up RAID1 on Inspiron 530
I'm attempting to set up RAID1 on my Inspiron 530. It came with a single 500 GB HDD installed. I just added, initialized, and formatted another 500 GB HDD. But that's about as far as I'm gettting. Consulting my Inspiron 530 manual, I attempted to set up my computer to "RAID-enabled mode" in Setup. The instructions are to 1. Press the up- and down-arrow keys to highlight Drive Controller, thenpress . and 2. Press the up- and down-arrow keys to highlight RAID On , and then press Enter. There's a problem right off the bat as there is no "Drives" entry in Setup. The closest thing is "Integrated Peripherals" menu, in which there is an option for SATA. By default, it is set to IDE. I tried changing this to the other option, RAID. However, my computer would not boot and attempted to repair itself via Setup Repair Mode, which it couldn't do. So I rebooted, switched that RAID option back to IDE, and the computer restarted okay. Despite not being able to complete the first step, I tried the next step in the process, using the Intel Matrix Storage Controller program. After not finding this anywhere on my computer, I downloaded two different versions from Intel. One is iata86enu.exe and the other is iata70_enu. Upon running these installs, I get a message stating "The computer does not meet the minimum requirements for installing this software. Setup will exit." So I'm not sure what I should do/try next? Any thoughts?
Responses (5)
Solutions (0)
wackybadger
7 Posts
523
1
Posted January 10th, 2009 22:00
I appreciate the reply. But those are exactly the instructions in the manual I was looking at. The manual states that if your computer was shipped set up to handle RAID then you would use the Intel Option ROM utility. If it was nto set up that way (as mine wasn't), then you first have to enable RAID in Setup and then use the intel matrix Storage Manager. But the instructions for both steps were not accurate. As I wrote, the method for enabling RAID in Setup was not as described. There was no 'Devices' menu in my BIOS. I did end up setting the 'SATA' option to 'RAID' from 'IDE' under the 'Integrated peripherals' menu, however. I then attempted several restarts, but couldn't get the PC to boot. It turns out the the PC was flashing the Intel Option ROM setup screen for a fraction of a second before attempting to boot. I caught a glimpse of the screen and it said to click CTRL+I to enter the RAID setup. So I did. I set the options appropriately (or so I thought) but the 'Select Disks' option was grayed out, so I couldn't change it, much less see which disk would be used for the RAID. So I clicked okay and exited the Option ROM setup. The computer then attempted to reboot itself only to discover that there were NO BOOTABLE DEVICES!!! Apparently, the inability to select which disk to use as the RAID disk resulted in the PC using the new blank HDD as the template for setting up the RAID and the blank HDD was copied over to the C: drive. It only took a few seconds and the I exited the Option ROM setup. Of course, I did this without backing up everything and so have lost the entire contents of my C: drive and currently cannot boot my PC. I put the HDD that used to be the bootable C: drive into another computer and it showed up in Disk Managment as both 'Offline' and 'Unallocated'. I initialized it but that's all I'm going to try for fear of making things worse than they are.
My question now is this...is the drive that was wiped (the former bootable C: drive) truly gone for good or are there some apps that can be put on bootable CD's that I can use to recover some of the data? Or is it possible to take it to a local computer repair shop (or send it somewhere) where they can try and recover the data? My understanding of hard drives is that when deleting and saving data, it's never really gone since it's just continually written over. Is this the same case when my RAID was being set up? Or did it really copy the empty drive sector by sector to the C: drive? Is there potentially recoverable data there? What gave me initial hope was that this 'copying' process took mere seconds so it couldn't really be written over that much...but then again if there wasn't anything to copy it wouldn't have to take that long. I've gotten in touch with Dell and they just tell me to reinstall Windows. But for that I need to dig for my Windows disc. And regarding reintalling Windows...do I need to have access to the recovery partition that was on the same HDD as the C: drive and is now also deleted? Or can simply pop in the Windows recovery disk from Dell into a completely blank drive? Either way, what is the purpose of that Dell recovery partition?
I greatly appreciate any and all help to my many questions. The irony is not lost on me, in that attempting to setup RAID1, I caused the very situation I was trying to avoid.
wackybadger
7 Posts
523
1
Posted January 10th, 2009 23:00
I should also add that I don't really know which type of RAID my PC was attempting to setup. I wanted to do a RAID1 but it's conceivable it may have tried to setup a RAID0. I dont' know. Thinking back, there just weren't that many options to select/change in the Intel Option ROM setup so I figured it must know what it was doing. Stupid me!
I have an Inspiron 530s. So the BIOS should be similar if not the same. Mine came with a non-RAID setup. In the manual it states it will only do RAID 1. The 530 manual only mentions RAID 1.
I can't answer your data recovery question and I do hope you are able to retrieve your data.
I created my RAID 1 differently using the Intel Matrix Storage Manager inside Windows instead of using the Intel ROM Utility.
Created a backup image of my system.
I selected RAID in the system SETUP.
Reinstalled my OS (Vista) and had the Intel SATA RAID driver on a thumb drive. During the install, I loaded the RAID driver.
Note: You have to reinstall your OS when you enable RAID in the system setup if your system was shipped non-RAID.
After the OS was installed, I installed the Intel Matrix Storage Manager. Selecting my target and member drive was easy and clearly identifiable. The RAID 1 process took ~1.5 hours for a couple of 320GB drives.wackybadger
7 Posts
523
1
Posted January 12th, 2009 12:00
That's what doesn't make sense to me. I didn't order my system with RAID, obviously, since it only came with 1 HDD. But based on reading the manual, it would seem that in some sense it was shipped with RAID. The manual says that if your system was shipped non-RAID you should use Intel Matrix Storage Manager inside Windows after you have enabled RAID in setup. Two problems with that were that Intel Matrix Storage Manager was not on my PC and if I first enabled RAID in setup, then my system would not boot - it would pause ever so briefly at the Intel Option ROM setup before failing to boot due to a 'Startup error'. So on a subsequent boot, I pressed Ctrl+I to enter the Option ROM utility and proceed to (incorrectly) setup the RAID1 array.I created my RAID 1 differently using the Intel Matrix Storage Manager inside Windows instead of using the Intel ROM Utility.
Created a backup image of my system.
I selected RAID in the system SETUP.
Reinstalled my OS (Vista) and had the Intel SATA RAID driver on a thumb drive. During the install, I loaded the RAID driver.
Note: You have to reinstall your OS when you enable RAID in the system setup if your system was shipped non-RAID.
After the OS was installed, I installed the Intel Matrix Storage Manager. Selecting my target and member drive was easy and clearly identifiable. The RAID 1 process took ~1.5 hours for a couple of 320GB drives.The other thing is that in the Dell Technology guide it says that there is an option to create a RAID1 array without reinstalling the OS. I don't know what to do anymore. Right now I'm just contacting various computer repair places to see what they think.

Der Tempel
29 Posts
523
1
Posted January 10th, 2009 04:00
Hi,
Set the Inspiron 530 to RAID-enabled mode
Enter System Setup.
Press the up- and down-arrow keys to highlight Integrated Peripherals and press enter to select.
Press the up- and down-arrow keys to highlight Drive Controller and then press .
Press the up- and down-arrow keys to highlight SATA Mode and then press to access the options.
Press the up- and down-arrow keys to highlight RAID, and then press to enable RAID.
Press to save and exit System Setup.
Creating a RAID1 volume on the Inspiron 530 with Intel matrix Storage Manager (installed)
-Set the computer to RAID-enabled mode.
-Click Start and then point to Programs>Intel Matrix Storage Manager>Intel Matrix Storage Manager to launch the Intel® Storage Utility application.
>> If you do not see an Actions menu option, you have not yet set the computer to RAID-enabled mode.
On the Actions menu, select Create RAID Volume to launch the Create RAID Volume Wizard.
Click Next at the first screen.
Confirm the volume name, select RAID 1 as the RAID level, and then click Next to continue.
On the Select Volume Location screen, click the first hard drive you want to use to create the RAID 0 volume, and then click the right arrow.Click a second hard drive until two drives appear in the Selected window, and then click Next.
In the Specify Volume Size window, select the volume size desired and then click Next.
Click Finish to create the volume, or click Back to make changes.
Follow Microsoft® Windows® procedures for creating a partition on the new RAID volume.
Hope this helps...