UNSOLVED

carlos.maiala

updated

12 years ago

0

100860

July 31st, 2014 10:00

Dell Power Vault TL2000 ISCSI BRIDGE (tl24iscsixsas 1gb iscsi)

Hello,


Iam having trouble with my tape library iscsi bridge, my scerario are:

1- Someone configured an ip on it before then it was not being used for long and the configuration was not documented.

2-I did a factory reset on the tape so i could try the default ip that is 10.10.10.10 (i follow the Iscsi bridge configuration manual)

3- i set an ip address on my laptop (10.10.10.11 with mask 255.255.255.0) and i connected my CAT5e cable on each port of the Iscsi bridge to ping 10.10.10.10 but i was not succeed, i need help so that i can have my iscsi bridge working, and one thing i notice is that the connection between my laptop and the iscsi bridge is at 10MB os speed is that NORMAL... Help help

  • DELL-Sam L

    Community Manager

    •

    8150 Posts

    •

    34715 Points

    1581

    0

    Posted July 31st, 2014 14:00

    Hello carlos.maiala,

    When you try to connect to the ISCSI Bridge are you using the ethernet port next to the sas connection on the ISCSI Bridge?  If not then the Left side ethernet port is the port that you will need to use to access the bridge for setup as that is the port that is set to 10.10.10.10.  It is normal for the connection speed of the management interface to be about 10mb speed.      

    Please let us know if you have any other questions.

  • 1581

    0

    Posted August 1st, 2014 00:00

    Sam,

    Yes, iam using the ethernet port next to the sas connection on the Iscsi Bridge, and i cannot connect to it

  • Claudio2

    1 Rookie

    •

    9 Posts

    1581

    0

    Posted March 4th, 2015 23:00

    Carlos,

    I ran into the same issue as you and I was able to solve it by using a utility that Dell support provided to me called LANSCAN.  This utility sends out a broadcast to the iSCSI card which then responds back with its IP address and other information.  It worked really well.  Contact Dell support and ask them for the utility.

  • woodchuck11

    1 Message

    1581

    0

    Posted February 9th, 2016 14:00

    Hi, sorry to bring this thread back but I'm having the same issue. Is it possible to obtain the LANSCAN utility?

  • Claudio2

    1 Rookie

    •

    9 Posts

    1581

    0

    Posted February 17th, 2016 22:00

    Woodchuck11,

                     Send me a private message with your e-mail address and I will send you the Lanscan utility via e-mail as an attachment.

    Claudio

  • kingwilliam

    1 Message

    1581

    0

    Posted December 10th, 2016 18:00

    I have same issue, can you email or private message with LANSCAN. thank you!

  • calbert7890

    1 Message

    1581

    0

    Posted December 25th, 2016 13:00

    Hi Carlos,

    I have the same problem. I can´t connect via ethernet on both ports with any ip-adress. A cisco swtch c-3750 doesn´t shows any mac adress from the iscsi-bridge. Where can I get the LANSCAN - utility.

    Best regards

    Carsten

  • uniwar

    2 Posts

    1576

    0

    Posted April 14th, 2017 02:00

    I have same issue, can you email or private message with LANSCAN. thank you!

  • badger2012

    1 Rookie

    •

    9 Posts

    1576

    0

    Posted July 6th, 2017 15:00

    Hi Sam

    could you please send me the lanscan utility so I can discover the ip address of my iscsi bridge

    thanks adrian

  • DELL-Sam L

    Community Manager

    •

    8150 Posts

    •

    34715 Points

    1022

    0

    Posted July 7th, 2017 14:00

    Hello Adrian,

    If you connect to the default port of your iSCSI bridge, can you use the default IP 10.10.10.10 to access the management utility? If not then you will need to direct connect to the default port of your iSCSI bridge. Once that is done then you can use any LAN scan utility that you prefer & it should find the IP of the bridge.

    Please let us know if you have any other questions.