UNSOLVED

CraigNi

updated

3 months ago

C

CraigNi

5 Posts

0

21681

April 14th, 2008 20:00

Drivers for poweredge blade 1855

I am going planning on upgrading our 1855 2003 server to 2008 server.  I noticed there are drivers available,

has anyone had any experiences doing this?

 

Thanks

Craig

  • 440

    0

    Posted April 15th, 2008 14:00

    By the way, the I may be a "newbie" to the forum like it claims, but I am not to Dell Hardware and Software setups. (Been doiing IT for 20 years now with the last 10 working on Network Servers to include Dell).
  • 440

    0

    Posted April 15th, 2008 14:00

    I am actually attempting this now on one of my 1855's. Since you can not do an in-place upgrade, I am going from scratch using the latest Dell Systems MGMT DVD that I downloaded. It has all the latest drivers for this server and other poweredge servers. I also made sure all firmware was up to date as well.I have run into a snag though. It runs through the initial Dell setup and then reboots to start the OS setup. Then it just stops at the lovely multi-color green Vista / 2008 screen and never asks for media or does anything else.

     

    I am currently rebuild my RAID from scratch to eliminate all possibilties of the old OS interfering. I will post later today to let you know what has happened and whether I have to bring Tech Support into the picture.

  • CraigNi

    5 Posts

    441

    0

    Posted April 17th, 2008 16:00

    Thanks George!

    Thats great news.  I'll try that immediately

     

    Craig 

  • 440

    0

    Posted April 17th, 2008 16:00

    Craig,

     

        I have done an install now. I had 2 servers I tested with. Using the Dell Systems mangement DVD seemed to add an inordinate amount of time to the install. I tried the second server with the Windows 2008 DVD straight up and it installed without a problem. Recognized all the hardware. I did update the drives from the Dell website after words to be on the safe side.

     

    So the quickest way is ton install str8 from the Windows 2008 media then update your drivers. Also make sure to update all firmware first.

  • twineee

    9 Posts

    441

    0

    Posted August 11th, 2009 11:00

    I also have the 1855 running Server 2008.

    I have an issue with the NIC driver, it installs a microsoft driver as bellow which works but i cannot team the adaptors.

    Intel(R) PRO/1000 MB Dual Port Server Connection
    Microsoft
    21/06/2006
    8.3.2.8

    I have downloaded the latest driver from Intel version bellow which installs but cannot see the adaptor

    intel
    23/09/2008
    8.3.15.0

    Has anyone else seen this issues and resolved it?

    Thanks in advance

     

    Dan

  • twineee

    9 Posts

    441

    0

    Posted August 11th, 2009 12:00

    I am already conncting to the console.

    When using the microsoft driver i dont see any intel options which makes sense as its a microsoft dirver

     

    on the intel driver mensioned above i do see the teaming option but there is an issue because the whole driver doesnt work.

     

    It installs but comes up with an error in devcie manager saying it couldnt find the hardware error cause 10

     

    can you confirm the correct intel driver version which should work?

  • Dev Mgr

    6 Operator

    •

    9308 Posts

    •

    3 Points

    441

    0

    Posted August 11th, 2009 12:00

    The Intel software doesn't show if you RDP into the server normally.

     

    From your desktop, do a Start -> Run -> "mstsc /console" and press enter. Now RDP in and see if in the device manager under the NIC properties you see the NIC teaming option.

     

    Alternatively, go in via the DRAC or a kvm (crashcart) attached to the blade (on the front).

  • gkuepper

    1 Message

    441

    0

    Posted September 24th, 2009 06:00

    We have the same problem.

    any results?

  • twineee

    9 Posts

    441

    0

    Posted September 24th, 2009 06:00

    We have the same problem.

    any results?

    No i'm still looking, let me know how you get on.

  • twineee

    9 Posts

    240

    0

    Posted October 2nd, 2009 05:00

    Has anyone found a solution to this?

    also i have two switch modules installed in my chasis whats the best way to have these configured.

    i curently have a very simple conf on both switches being the same can i have some suggestions?

    console# sh run
    interface vlan 1
    ip address 10.0.10.8 255.255.255.0
    exit
    ip default-gateway 10.0.10.253