UNSOLVED

iworkwfreax

updated

10 months ago

I

iworkwfreax

1 Rookie

•

10 Posts

0

7481

October 12th, 2018 08:00

S4112F-ON breakout 40Gb

I have both manually broken out eth1/1/15 and turned on autobreakout on a S4112F-on.  I am trying to connect eth1/1/15 to S4048T-ON for1/49.  Although the cable is recognized (Dell DAC-QSFP-40G), I can't get the switches to link.  Any help is appreciated.

  • iworkwfreax

    1 Rookie

    •

    10 Posts

    6042

    0

    Posted October 15th, 2018 09:00

    S4112F-ON:

    interface ethernet1/1/15:1
     no shutdown
     switchport access vlan 900
    
    Ethernet 1/1/15:1 is up, line protocol is down
    Hardware is Dell EMC Eth, address is 20:04:0f:08:61:a0
        Current address is 20:04:0f:08:61:a0
    Pluggable media present, QSFP-PLUS type is QSFP_40GBASE_CR4_1M
        Wavelength is 38
        Receive power reading is
    Interface index is 17305433
    Internet address is not set
    Mode of IPv4 Address Assignment: not set
    Interface IPv6 oper status: Disabled
    MTU 1532 bytes, IP MTU 1500 bytes
    LineSpeed 0, Auto-Negotiation on
    Flowcontrol rx off tx off
    ARP type: ARPA, ARP Timeout: 60
    Last clearing of "show interface" counters: 3 days 01:53:21
    Queuing strategy: fifo
    Input statistics:
         0 packets, 0 octets
         0 64-byte pkts, 0 over 64-byte pkts, 0 over 127-byte pkts
         0 over 255-byte pkts, 0 over 511-byte pkts, 0 over 1023-byte pkts
         0 Multicasts, 0 Broadcasts, 0 Unicasts
         0 runts, 0 giants, 0 throttles
         0 CRC, 0 overrun, 0 discarded
    Output statistics:
         0 packets, 0 octets
         0 64-byte pkts, 0 over 64-byte pkts, 0 over 127-byte pkts
         0 over 255-byte pkts, 0 over 511-byte pkts, 0 over 1023-byte pkts
         0 Multicasts, 0 Broadcasts, 0 Unicasts
         0 throttles, 0 discarded, 0 Collisions, 0 wred drops
    Rate Info(interval 30 seconds):
         Input 0 Mbits/sec, 0 packets/sec, 0% of line rate
         Output 0 Mbits/sec, 0 packets/sec, 0% of line rate
    Time since last interface status change: 3 days 01:53:22
    
    

     

  • iworkwfreax

    1 Rookie

    •

    10 Posts

    6026

    0

    Posted October 15th, 2018 10:00

    S4048T-ON

    interface fortyGigE 1/49
     no ip address
     switchport
     no shutdown
    
    Hardware is DellEMCEth, address is e4:f0:04:c2:08:ad
        Current address is e4:f0:04:c2:08:ad
    Pluggable media present, QSFP type is 40GBASE-CR4-1M
    Interface index is 2103301
    Internet address is not set
    Mode of IPv4 Address Assignment : NONE
    DHCP Client-ID :e4f004c208ad
    MTU 1554 bytes, IP MTU 1500 bytes
    LineSpeed 40000 Mbit
    Flowcontrol rx off tx off
    ARP type: ARPA, ARP Timeout 04:00:00
    Last clearing of "show interface" counters 3d19h23m
    Queueing strategy: fifo
    Input Statistics:
         0 packets, 0 bytes
         0 64-byte pkts, 0 over 64-byte pkts, 0 over 127-byte pkts
         0 over 255-byte pkts, 0 over 511-byte pkts, 0 over 1023-byte pkts
         0 Multicasts, 0 Broadcasts, 0 Unicasts
         0 runts, 0 giants, 0 throttles
         0 CRC, 0 overrun, 0 discarded
    Output Statistics:
         0 packets, 0 bytes, 0 underruns
         0 64-byte pkts, 0 over 64-byte pkts, 0 over 127-byte pkts
         0 over 255-byte pkts, 0 over 511-byte pkts, 0 over 1023-byte pkts
         0 Multicasts, 0 Broadcasts, 0 Unicasts
         0 throttles, 0 discarded, 0 collisions, 0 wreddrops
    Rate info (interval 299 seconds):
         Input 00.00 Mbits/sec,          0 packets/sec, 0.00% of line-rate
         Output 00.00 Mbits/sec,          0 packets/sec, 0.00% of line-rate
    Time since last interface status change: 3d19h22m
  • iworkwfreax

    1 Rookie

    •

    10 Posts

    6030

    0

    Posted October 15th, 2018 10:00

    S4048T-ON

    interface fortyGigE 1/49
     no ip address
     switchport
     no shutdown
    
    Hardware is DellEMCEth, address is e4:f0:04:c2:08:ad
        Current address is e4:f0:04:c2:08:ad
    Pluggable media present, QSFP type is 40GBASE-CR4-1M
    Interface index is 2103301
    Internet address is not set
    Mode of IPv4 Address Assignment : NONE
    DHCP Client-ID :e4f004c208ad
    MTU 1554 bytes, IP MTU 1500 bytes
    LineSpeed 40000 Mbit
    Flowcontrol rx off tx off
    ARP type: ARPA, ARP Timeout 04:00:00
    Last clearing of "show interface" counters 3d18h52m
    Queueing strategy: fifo
    Input Statistics:
         0 packets, 0 bytes
         0 64-byte pkts, 0 over 64-byte pkts, 0 over 127-byte pkts
         0 over 255-byte pkts, 0 over 511-byte pkts, 0 over 1023-byte pkts
         0 Multicasts, 0 Broadcasts, 0 Unicasts
         0 runts, 0 giants, 0 throttles
         0 CRC, 0 overrun, 0 discarded
    Output Statistics:
         0 packets, 0 bytes, 0 underruns
         0 64-byte pkts, 0 over 64-byte pkts, 0 over 127-byte pkts
         0 over 255-byte pkts, 0 over 511-byte pkts, 0 over 1023-byte pkts
         0 Multicasts, 0 Broadcasts, 0 Unicasts
         0 throttles, 0 discarded, 0 collisions, 0 wreddrops
    Rate info (interval 299 seconds):
         Input 00.00 Mbits/sec,          0 packets/sec, 0.00% of line-rate
         Output 00.00 Mbits/sec,          0 packets/sec, 0.00% of line-rate
    Time since last interface status change: 3d18h51m
  • iworkwfreax

    1 Rookie

    •

    10 Posts

    6020

    0

    Posted October 15th, 2018 12:00

    S4048T-ON for1/49   <-> S4112F-ON eth1/1/15:1

    My understanding was that the S4112F-ON could be broken out to 40Gb.  This is a  100GbE (QSFP28) port.  I tried breakout "manually" to 40 Gb with:

    interface breakout 1/1/15 map 40g-1x

    It is currently configured with the "feature auto-breakout".   Neither have provided me a link.  

    The cable is DAC-QSFP-40G-1M 05NP8R.

  • iworkwfreax

    1 Rookie

    •

    10 Posts

    6007

    0

    Posted October 15th, 2018 13:00

    The end goal is to have them both as trunks with all vlans tagged.  I have tried it both with and without vlan configured.  Doesn't seem to make a difference.

  • iworkwfreax

    1 Rookie

    •

    10 Posts

    1978

    0

    Posted October 25th, 2018 11:00

    Can't manually set the speed but this put me on the right path.  Had to turn negotiation off on the 4112.  Thanks for the help.

  • SionWork

    1 Message

    1299

    0

    Posted January 8th, 2020 00:00

    Hi did you ever resolve this I have the same issues. 

     

  • Behemott

    1 Rookie

    •

    12 Posts

    0

    0

    Posted January 22nd, 2026 19:01

    Just fixed the same issue with a simple #negotiation off on the S4112.

    My set-up is a S4048 mode trunk with a S4112.

    Hardware is a Dell DAC QSFP+ 40GBASE-CR4-0.5M
    Breakout map is set at #breakout 1/1/15 map 40g-1x

    Its a bit late but I hope it helps someone here...