1600n scanner glass has film coating foggy cloudy on bottom - how to clean?
My Dell 1600n multifunction printer has a film coating or foggy/ cloudy on the underside of the scanner glass platen. It doesn't look like I can access the underside of the glass so how am I supposed to clean it? It is affecting my copy quality where it is dirty.
If the printer is still under warantty call Dell for a replacment if not try and cleaning all the pieces of glass not only the big piece from the top it may help.
Also for your info there is no way to clean the bottom portion of the glass on the printer.
I've got several (about 25) of these units and they all seem to be developing the foggy residue on the underside of the glass. It took most of them about 2 to 3 months for the film to start coating the underside of the glass. They still print fine, but copies and faxes are very faint, and my end-users tend to get upset about unreadable copies.
Obviously this isn't a new problem:
http://reviews.cnet.com/Dell_1600n/4864-3181_7-30898420.html?messageSiteID=7&messageID=1140562&cval=1140562&ctype=msgid
Dell needs to provide info on how to get to the underside to clean it, or start assembling these things with adhesive that doesn't vaporize and stick to the glass.....otherwise I see a big class-action in the making.
If anyone has figured out how to remove the glass without breaking anything, please post it here.
This is my experience with the 1600n underglass haze. I bought two units, both of which had the haze which has gotten thicker over the months. I finally got around to calling in to dell support. The explaination I got from tech support was as follows: There is a gas inside that is meant to keep the underside of the glass clean. However, when this gas is exposed to air, it turns into a gray haze, and thus coats the underside of the glass. So, if you have haze under the glass, that means there is a leak in the system, and, as more air is introduced into the system through the leak, the haze will accumulate thicker and thicker with time.
Dell has sent me a replacement (refurbished) unit overnight, unfortunately, the replacement suffers from the same fate, and another one is being sent with a special request to inspect the glass prior to shipment. I am impressed with the speed with which the replacements are being sent, however, the product quality is far from impressive
I got to the underside of the glass with little probelm. I actually had taken the whole thing almost all apart when I decided to attack the FOG. I could post here. Let me know if still interested. I think my power supply has died, tho.
@mollerartiste wrote:
I got to the underside of the glass with little probelm. I actually had taken the whole thing almost all apart when I decided to attack the FOG. I could post here. Let me know if still interested. I think my power supply has died, tho.
@mollerartiste wrote:
I got to the underside of the glass with little probelm. I actually had taken the whole thing almost all apart when I decided to attack the FOG. I could post here. Let me know if still interested. I think my power supply has died, tho.
Please tell us how you did it!
Here is a link to fix the problem. Please write me if this is helpful.....
I just noticed the same problem, one week after my warranty expired. I don't see any response from Dell. Hellllooo! Does anyone from Dell tech support actually monitor or attempt to answer posted questions? This is a serious problem, which Dell has evidently known about for quite some time.
Neither the address nor the link to information on getting to the underside of the glass in the earlier response go anywhere.
INSTRUCTIONS FOR CLEANING THE GLASS ON THE DELL 1600n MFP
Generally the plastic on the printer needs to come off; unplug all cords; need small phillips head screw driver.
Remove the paper tray and toner cartridge and set to the side out of the way.
Remove the four recessed screws on the back side and remove the panel.
Remove the four recessed screws & four visible screws on the front side. These screws are behind the toner access panel & previously removed paper tray. Four screws each on the left and right sides when looking at it from the front.
Place printer on its right side to remove one screw on the left side panel; the screw is accessed near the back and bottom.
Remove left panel by lifting up on the three tabs that lock on the bottom. The left panel is lifted/tilted from the bottom by the tabs to the top; a little wiggling should break it free. Unplug speaker wire from circuit board.
Place printer on its left side.
Remove right panel by lifting up on the three tabs that lock on the bottom. The right panel is lifted/tilted from the bottom by the tabs to the top; a little wiggling should break it free.
Remove front display panel cover by lifting up on the lip on the front edge. The front display panel cover is lifted/tilted from the front; a little wiggling should break it free.
Remove the three recessed screws on the lower front side of the front display panel. The front display panel is lifted/tilted from the front; a little wiggling should break it free.
Remove paper clip panel cover on the far left of the front display panel.
Remove top pivoting cover that sits over scanner. This lifts out on the top rear.
Remove the two screws on the top front side of the glass panel assembly.
Remove the two recessed screws on the top back side of the glass panel assembly.
Lift off the glass panel assembly; use fingers along left and right edges to tilt the assembly up; a little wiggling should break it free.
Clean all the glass surface with a good cloth towel (lint free) and a foaming glass cleaner.
Reverse the order to put back together; take your time and be careful. Good Luck!!
Searchy
64 Posts
688
0
Posted January 29th, 2006 05:00
If the printer is still under warantty call Dell for a replacment if not try and cleaning all the pieces of glass not only the big piece from the top it may help.
Also for your info there is no way to clean the bottom portion of the glass on the printer.