I made the fatal mistake of allowing Dell Update to run on my system and it has installed a Intel UHD Driver update that has sent me back to square one with NONE of my screens attached to my Dell Dock being able to display in their native resolution.
My brand new Latitude 7640 connected to my Dell WD22TB dock is only able to display in 1920x1080 (instead of the native 1920x1200) on my HP LP2465 main monitor and just 1280x1024 (instead of 1600x1200) on my 2 HP2065 side monitors. Everything is just a blurry mess!
Thank you, FeRDNYC. You've offered more assistance than anyone from this hopeless mega-computer corp combined.
My bad! You're correct, the LP2465 native resolution is 1920x1200 which I wasn't able to recall as I wrote the original post through blurry low resolution screen. I've since corrected it in my original post.
Yes, it's a WD22TB4 that's still under support warranty.
The two 1600x1200 LP2065 monitors connect to the dock via a DP-to-DVI cable each that was working absolutely fine in my setup before the driver update.
Unfortunately, none of those BIOS (UEFI) settings made a difference. Even with just a single monitor plugged in isn't able to get it to display in it's native resolution with all of those settings configured accordingly. There are discussions on other threads that seems to indicate it's the dock being a dumb brick in trying to communicate what are the monitors are being plugged in to the GPU driver :
Thankfully, I've managed to get my original setup back up and working by using Display Driver Uninstaller to absolutely nuke the display driver to oblivion and everything related to it: unpluggged monitor configurations, setting files, registry entries, apps, folders, everything! I did not use DDU in my previous attempts to reinstall the older driver last known to work: 31.0.101.4502. Once the old driver was back on my laptop, everything returned the way they were as before.
The only other thing had to do was take a hammer to the Windows Update group policy configuration to ban it from installing anymore drivers as that dumb program would immediately screw me back to square one with the latest (faulty) driver it sees the moment it runs.
only able to display in 1920x1080 (instead of the native 1920x1400) on my HP LP2465 main monitor
That threw me, initially, since it sounded like such a strange resolution. But I looked up the specs, and your HP L2465 has the same 1920×1200 (16:10 aspect) native resolution as my own HP Z24i, so that makes sense. The big irony here is that 1920×1200 is the exact same resolution as your laptop's own internal display! But, that's neither here nor there when it comes to dock support.
The dock you have is the WD22TB4, yes? (I don't think there's any other model of WD22TB, but I figured I should check.) I've been reading the specs for its display support — man, is this thing complex! The available resolutions are a twisty maze of port and setting combinations that take multiple tables spread over 5 pages of the docs to fully lay out. And it's full of notes like this:
NOTE: HDMI 2.0 and MFDP (Multi-Function DisplayPort) Type-C ports on the back of are toggled. HDMI 2.0 and MFDP Type-C cannot support dual monitors simultaneously. Only one of these ports can be used at a time.
NOTE: If higher resolution monitors are used, the Graphics driver makes a judgment based on monitor specifications and display configurations. Some resolutions may not be supported and so will be removed from the Windows Display Control Panel.
Apparently what it all comes down to is the available bandwidth between the laptop and the dock, which has a huge impact on available resolutions. But, of course, after telling you that, they don't provide any means of checking how much bandwidth is currently available to a connected dock.
It's also a bit unfortunate that your HP L2465 is the one you're connecting via HDMI, as that port is the first to sacrifice resolution when bandwidth is limited. There are several three-monitor configurations that do list the HDMI port as being limited to 1920×1080. Although in most of those, the DisplayPort ports support the same or better resolution, so that still doesn't explain the lack of 1600×1200 on the HP 2065s.
I do see a number of combinations that could possibly limit screen resolution to the levels you're reporting, but they'd all require the dock to be connected to a non-Thunderbolt host with the absolute minimum available bandwidth.
Still, a couple of questions, and a few suggestions:
How are you connecting all of the screens?
You mentioned HDMI for the L2465. I see that it only offers dual DVI inputs, so I assume that's using an HDMI - to - DVI-D cable?
I'm guessing the two HP 2065 are plugged into the dock's two DisplayPort ports? Those screens also offer only dual DVI inputs, so again probably using DisplayPort - to - DVI-D cables?
What OS are you running? (I only ask that because of a note in the WD22TB4 manual, which could affect available bandwidth):
Linux operating system is unable to physically turn-off built-in display, the external display numbers will be one less than the display numbers listed in above tables.
Now, the suggestions:
Everything I'm seeing in the WD22TB4 documentation about such severely restricted resolutions would require that it be connected to a non-Thunderbolt host, which your laptop shouldn't be as it fully supports Thunderbolt 4 on both of its left-side USB-C ports. One possibility is that you aren't using Thunderbolt 4 for the connection, though.
There are some BIOS settings on the 7640 that would greatly affect the bandwidth available to the dock. The most important seem to be:
Enable External USB Ports which should be enabled (the default)
Enable USB Boot Support which should be enabled by default
Integrated Devices > Enable Thunderbolt Technology Support which is absolutely critical to have enabled (the default), and could cause the issues you're seeing if disabled.
Integrated Devices > Enable Thunderbolt Boot Support is disabled by default, but might be worth enabling if you're booting up the laptop with the dock connected, as it could perhaps affect display detection?
Integrated Devices > Enable Thunderbolt (and PCIe behind TBT) pre-boot modules is again disabled by default, but might be worth enabling in case it affects startup detection of the dock and its connected screens.
Integrated Devices > Video/Power only on Type-C Ports is disabled by default, and probably should not be enabled if you want to take full advantage of the dock's capabilities.
Integrated Devices > Type-C Dock Override is enabled by default, and apparently lets your laptop BIOS configure what peripherals are available via a dock connection. Additionally, by default Type-C Dock Audio and Type-C Dock Lan are enabled by default. I don't have a lot of advice on those, although if you are dealing with issues of limited bandwidth, disabling the dock audio and ethernet might help. But if you're actually getting a Thunderbolt 4 link to the dock, that shouldn't be an issue, so probably better to focus on that first.
Can't hurt to check all of those settings, to make sure they're at sane values. Hope this helps!
Seriously, Dell!??! What's the 🤬 point of offering bulleted-list formatting in the post editor, if you're just going to style the list markers and indents out of existence and make the list look like crap?
Well, I'm glad to hear you found... I'd term it a workaround, personally, since it sounds like the issue is far from really solved on Dell's part, and you shouldn't be forced to go through that much hassle.
Unfortunately, none of those BIOS (UEFI) settings made a difference. Even with just a single monitor plugged in isn't able to get it to display in it's native resolution with all of those settings configured accordingly.
Well, that's unfortunate to hear. It sounds like they may have just completely broken Thunderbolt support in the newer driver package, somehow.
There are discussions on other threads that seems to indicate it's the dock being a dumb brick in trying to communicate what are the monitors are being plugged in to the GPU driver :
Yeahhhh... I don't know. I mean, if that were the case, how would it work with the older drivers?
Display identification and configuration is a difficult problem, to be sure. Especially when dealing with screens that may be at the remote end of multiple interface connections that translate the signal between protocols along the way.
As much as it was no fun either, in some ways it was a lot easier when you had to manually configure all of the timing and size parameters for each display on the system, all communication flowed in one direction, and if you got the numbers too far off spec your monitor just started smoking. Easy-peasy!
OTOH! It's the the year 20-frickin'-23, they've had over FORTY YEARS to iterate on this stuff, and how can companies possibly still fail to build devices (and write software) that can to do it properly!?
I got a partial solution working with the new drivers. I nuked all Intel and Nvidia drivers, and used CRU (Custom Resolution Utility) to set the resolution of the screens. This seemed to be a pot luck in getting it working approach (took 3 or 4 attempts), and I was only able to get the 2x NEC LCD2190UXp working at 1600x1200@60hz.
I was not ever able to get the NEC LCD2490WUXi2 at 1920x1200@60hz.
I then cheated, and plugged the NEC LCD2490WUXi2 into the HDMI port of the USB-C mini hub adapter that came with the XPS 15, and then plugged that into one of the WD22B4 Tunderbolt4 ports. After rebooting there was a warning about stacking 'hubs', which I ignored. This then allowed the NEC LCD2490WUXi2 to display 1920x1200@60hz correctly.
I'm now going to order a TB4-DVI cable and see if that works to avoid the 'hub stacking'error.
I had issues with WD22TB4 and Dell 5570 external also. My setting is three 4k monitors connecting via WD22TB4 to DELL 5570. After the Intel video card driver update, there would be only one monitor at 4K and other two not. Tried many way to solve it. The final solution is to download the earliest Intel video card driver and install it. And after the installation, don't even think about updating the Intel Video Card driver. I had tried multiple times without success. Hope this give you some hints. Good luck!
BenjaminWKI
1 Rookie
•
8 Posts
0
1
Posted October 18th, 2023 02:49
Thank you, FeRDNYC. You've offered more assistance than anyone from this hopeless mega-computer corp combined.
My bad! You're correct, the LP2465 native resolution is 1920x1200 which I wasn't able to recall as I wrote the original post through blurry low resolution screen. I've since corrected it in my original post.
Yes, it's a WD22TB4 that's still under support warranty.
The two 1600x1200 LP2065 monitors connect to the dock via a DP-to-DVI cable each that was working absolutely fine in my setup before the driver update.
Unfortunately, none of those BIOS (UEFI) settings made a difference. Even with just a single monitor plugged in isn't able to get it to display in it's native resolution with all of those settings configured accordingly. There are discussions on other threads that seems to indicate it's the dock being a dumb brick in trying to communicate what are the monitors are being plugged in to the GPU driver :
https://www.dell.com/community/en/conversations/xps/wd22tb4-docking-station-a-story-of-the-gross-incompetence-of-dell-support-and-engineers/647f9df2f4ccf8a8de27083c
https://community.intel.com/t5/Graphics/Iris-Xe-not-going-above-1280x1024-when-using-Dell-dock/td-p/1353493
Thankfully, I've managed to get my original setup back up and working by using Display Driver Uninstaller to absolutely nuke the display driver to oblivion and everything related to it:
unpluggged monitor configurations, setting files, registry entries, apps, folders, everything!
I did not use DDU in my previous attempts to reinstall the older driver last known to work: 31.0.101.4502.
Once the old driver was back on my laptop, everything returned the way they were as before.
The only other thing had to do was take a hammer to the Windows Update group policy configuration to ban it from installing anymore drivers as that dumb program would immediately screw me back to square one with the latest (faulty) driver it sees the moment it runs.
I still get the occassional blank screen that's been reported in this thread from February: https://www.dell.com/community/en/conversations/latitude/dell-latitude-5530-dell-thunderbolt-dock-wd22tb4-flickering-screen/647fa235f4ccf8a8de7a3387
(That's still unsolved and ignored by the incompetent Dell staff to this date. Colour me absolutely surprised!)
But I would happily take the occassional blank screen over a blurry mess from this faulty product.
(edited)