UNSOLVED

zitsky

updated

18 years ago

Z

zitsky

1 Rookie

•

6 Posts

0

98419

October 26th, 2008 11:00

MD3000 failed firmware update?

I'm trying to connect to an MD3000 to read the service tag which is missing from the outside of the unit.  There's no paperwork to show what the service tag is, unfortunately.  I did talk to one person in Dell support that was able to give me general advice.  I'm hoping someone here might know something more specific.

 

I managed to get a hold of the Dell password reset cable, as mentioned in another post.  Once connected, I do get a response from the system, but not what I expect.  I'm getting what appears to be a VXworks login, and not the Powervault console that I expect.  

 

I should note that (to my surprise), neither of the raid controllers installed in the MD3000 have the BBU.  They were either removed at some point, or never ordered.  I plan to order new ones to install, but would a missing BBU keep the unit from booting?

 

When connecting to the serial console, I get two options, either to press CTRL-BREAK to set baud rate, which works, or to press for the service menu.  No matter how many times I press the "S" key it never takes me into the service menu, which I suspect might let me reload a new firmware image.  (Maybe I should be trying CTRL-S instead?)  Even if I get into the service menu, I'm not sure what good that would do me.  The only way I know to load firmware on these units is through the storage manager application.

 

->
Press within 5 seconds: for Service Interface, for baud rate

C interp: unknown symbol name 'sssssssssss'.
->
Press within 5 seconds: for Service Interface, for baud rate
Set baud rate: press within 5 seconds
Baud rate set to 115200

 

 

I managed to figure out the IP address of the raid controllers by connecting a laptop with a network sniffer.  When I try telneting to this IP, I get a VXworks login, but I have no idea of the username/password to try.If point the storage manager to the IP, I get a message about system in degraded state or similar, and I'm not able to see any information (all storage manager tabs are blank).

 

If I power on the unit with the serial cable/password reset cable attached, this is the output at startup.

 

10/26/08-01:02:10 (GMT) (tRootTask): NOTE:  I2C transaction returned 0x0423fe00

Reset, Power-Up Diagnostics - Loop 1 of 1
3600 Processor DRAM
     01 Data lines                             Passed
     02 Address lines                          Passed
3300 NVSRAM
     01 Data lines                             Passed
5900 Ethernet 91c111 #1
     01 Register read                          Passed
     02 Register test                          Passed
3A00 NAND Flash
     06 Bad Blocks Test                        Passed
2310 Application Accelerator Unit
     01 AAU Register Test                      Passed
6D00 LSI SAS 1068 IOC--Base Board
     01 IOC Register Read Test                 Passed
     02 IOC Register Address Lines Test        Passed
     03 IOC Register Data Lines Test           Passed
6D01 LSI SAS 1068 IOC--Host Card
     01 IOC Register Read Test                 Passed
     02 IOC Register Address Lines Test        Passed
     03 IOC Register Data Lines Test           Passed
3900 Real-Time Clock
     01 RT Clock Tick                          Passed
Diagnostic Manager exited normally.


Kernel initialization complete


Current date: 10/25/08  time: 19:10:30

LSI Logic RAID Controller
Copyright 2005-2008, LSI Logic Corporation.  All Rights Reserved.
Copyright 1984-2006 Wind River Systems, Inc.
VxWorks: VxWorks 6.4   Kernel: WIND version 2.10
Model: 1332    Firmware version: 97.35.11.66

Serial Port shell started.
->
->

 Dell has only been partially helpful, since I don't have the service tag.  But I can't get the service tag until I can get this in a managed state and read the tag that's encoded on the midplane.  

 

Does anyone have any suggestions for restoring the firmware to working condition?  

  • dzenz

    175 Posts

    823

    0

    Posted October 29th, 2008 20:00

    The mechanism to electronically read the Service Tag from a MD3000 is by using the Modular Disk Storage Manager. MDSM is also the console used to update the storage array firmware.

     

    Obviously if the array is not booting for some reason and you don't have the paperwork then there's a catch-22.

     

    Maybe try booting the array with one controller in slot 0 at a time?

     

    Dave

  • zitsky

    1 Rookie

    •

    6 Posts

    823

    0

    Posted October 29th, 2008 20:00

    I think I've tried that, but will try again.  Would this happen if the array doesn't recognize the hard drives, e.g. if they are uncertified?  Can anyone tell me what output they get on the serial connection if the connect the password reset cable to an MD3000 with no drives installed?  I've ordered two additional drives that are on the Dell compatibility list, just in case the ones I have are faulty.  I didn't want to fully populate this until I knew the unit was working, since it was purchased used, and I couldn't verify the warranty status.

     

    From looking at the network trace, and configuration, it looks as if the unit might be trying to boot the firmware from an NFS or TFTP mount.  I didn't even think this was possible.  

     

     


     

  • dzenz

    175 Posts

    823

    0

    Posted October 29th, 2008 21:00

    Yes, this could happen if the array did not recognize the drives as Dell certified ones. As least two (certified) drives have to be installed in the array.

     

    The storage array boots internally not off of the network.

     

    Dave

  • npapad

    9 Posts

    823

    0

    Posted March 2nd, 2009 13:00

    Have you tried typing a CAPITAL S after sending a break signal  in hyperterminal.

    Nick