I just replaced the system board in a 1400. Now, the box wont boot at all, no fan or anything. I've tried another power cable and made sure the control cable is in place. Is there any other way to test if the power supply died? Any suggestions? Thanks.
I have the same pb of no boot than you on my pe 1300 since I just disconnect mo power supply from the MB.. Didn't get any answer too... I have seen a power button on the MB itself, you can try it. I checked the voltage on the button (bridge of 3 V when you power on), and I have the stdby led green. But not able to have the power led green / to boot anymore ;-((
Alright everyone, yes this is an old thread but considering i have only just experienced the same issue and solved it means i would like to add a little advice to those traveling in the same boat, or those unfortunate to be in the future.
First of all, no thanks to dell for this one. There is absolutely no response from any technical support representative as to what we can do when this situation arises. No helpful insights, no possibilities, nothing. Oh, "want a new server?"
We experienced a similar issue just the other day when the system powered done completely out of the blue. When i say powered down, it was not a graceful OS shutdown, but rather an immediate termination. I took the system apart to trace any problems: examined the motherboard to find nothing obviously apparent, checked each of the capacitors to see whether they leaked or bulged, used a multimeter to check connections from SW_PWR buttons on board and remote power-up control board on the front bezel. Everything was fine and nothing could have been wrong with it. I was sure.
I examined the PSU to find that the 3.3v and 5v rails were still operating fine. They powered the onboard NIC and the standby LED was also green showing that the board was getting power. This is the problem: you can't accurately diagnose the issue as both components appear to be working correctly.
Now, through deduction i was of the opinion that the PSU was indeed faulty. In standard PSU's (read non-Dell) there is a green wire leading back to the PSU from the 20-24pin ATX12 (aka EPS12V) power cable that tells it to power up on the press of either the on-board power switch or via the separate power panel on the front bezel. In this case i was running on the assumption that the PSU was simply not initialising on the press of the power-up button. As a matter of fact, placing one of the meter probes to the power socket and the other on the power switch, you can clearly see a voltage drop that the PSU reads to signal a startup. In this case, the board provided the signal, but the PSU failed to switch to full power-up mode.
Searching for a replacement PSU was not easy. Apparently, when your system is out of warranty, there is a 3-5 day lead time for any item you purchase via Dell Parts. I am told by a Dell rep that this is akin to a penalty for the machine falling out of cover. Well, two fingers to you too Dell.
Searching for the item (in the UK) was not easy, much to my surprise especially for a server system only 4 years old. I can understand the issue for a desktop, but shocking for a server. The exact PSU model number can be found on this site (i believe its DP/N 6C783, NPS-330DB, 330W 5-V), however there are alternatives available (DP/N 1H070, 330W,PFC). These will work correctly.
The suppliers i have been told in the UK, who can provide these units are from either www.ServiceSource.co.uk or www.Upgrade.co.uk. They have the items in stock and can supply it to you next day.
Now, a word of warning. Do NOT use a standard 24-pin ATX PSU available off the shelves of any PC shop. Dell, in its arogant and infinite wisdom, has not followed standards and so the wiring and pin-outs of the Dell branded PSU's are completely different. There is no green wire for PSU power up (i think its the grey/slate wire) and after running a standard 24-pin PSU side-by-side with the faulty Dell branded PSU i managed to find out all but 3 wires. Its not worth the risk, since the motherboard will almost always be in good shape, modern-day low-voltage electronics are very reliable and resilient. Remember this when you next troubleshoot a similar issue.
tretcha
2 Posts
540
0
Posted November 21st, 2002 10:00
hi,
I have the same pb of no boot than you on my pe 1300 since I just disconnect mo power supply from the MB.. Didn't get any answer too... I have seen a power button on the MB itself, you can try it. I checked the voltage on the button (bridge of 3 V when you power on), and I have the stdby led green. But not able to have the power led green / to boot anymore ;-((