UNSOLVED

khammo01

updated

21 years ago

K

khammo01

27 Posts

0

16242

December 31st, 2005 23:00

DVI-connected 2405FPW goes into power save mode at 1920x1200x32

I have a new 2405FPW and love it, but it erratically enters power save mode when connected at the prime resolution and 32 bit color depth when connected via the DVI port.
I have an ATI X700 video card which according to the manufacturer site is designed to drive this resolution. I am using the dual link DVI monitor cable included with the monitor.
 
Everything works fine using the D-SUB connector, but the picture quality is not as good and I the image auto-adjust feature is not quite right which requires some adjustment every time I switch resolutions.
 
I can tell this is obviously a DVI issue - it only happens when connected using the DVI port and only at the higher data transfer rates (video works fine if I use 16bit color @ 1920x1200 ).
 
I doubt that the problem would go away if I got the monitor replaced. Any help appreciated. It would be especially helpful if someone could respond who has been able to successfully use the monitor with an ATI X700 at 1920x1200x32bit.
 

Message Edited by khammo01 on 12-31-2005 07:58 PM

  • burntham77

    1 Message

    700

    0

    Posted January 2nd, 2006 00:00

    I am having the exact same problem. Any solution would be appreciated.
  • chulett

    581 Posts

    700

    0

    Posted January 2nd, 2006 12:00

    How exact? What video card (etc) do you have?
  • 702

    0

    Posted January 4th, 2006 00:00

    I can confirm this behavior: Erratic powersaves in 1920x1200x32 via DVI, can sometimes be restored by powercycling display or computer. Graphics card is an ATI X700, lower resolutions work fine. Playing with options such as `Alternate DVI operating mode' or `Reduce DVI frequency for high-resolutions' do not affect this glitch.
  • chulett

    581 Posts

    702

    0

    Posted January 4th, 2006 01:00

    So... the common element here is an ATI X700 video card? Is this a known issue with the card at that rez?
  • khammo01

    27 Posts

    702

    0

    Posted January 8th, 2006 12:00

    Has anyone here tried with another (non ATI X700) card and noticed the problem disappear? I would be willing to upgrade the graphic card if I could be sure it would make this problem go away.
     
    If so, I am suspecting the digital signal quality from the X700 is weak or noisy, confusing the monitor.
     
  • khammo01

    27 Posts

    702

    0

    Posted January 8th, 2006 12:00

    I just got a 3 meter dual link cable that is a lot thicker than the cable the monitor came with but it doesn't seem to be helping.
     
    Can we get a Dell support representative to provide some input here please?
  • chulett

    581 Posts

    702

    0

    Posted January 8th, 2006 13:00

    Well... I'm running mine from an Nvidia (BFG) 7800GTX and having zero problems.

    If you are in the market for a video card upgrade, that would seem to be one way to solve the problem. You may also be a victim of a bad 'batch' of X700s - I'd be curious if anyone here has an X700 paired to a 2405FPW and doesn't have the problem. By chance, do you have any warranty on the card, the ability to have it replaced?

  • khammo01

    27 Posts

    702

    0

    Posted January 19th, 2006 10:00

    An update for everyone - I scrounged up some cash to buy an ATI X1600 XT, and have been running all day without the power save problems.
    So, if you have an X700 and are having this problem, sell it on eBay. That's your problem, not the cables or the monitor!
     
     
  • kanenas1

    10 Posts

    702

    0

    Posted February 17th, 2006 18:00

    What if it's Windows that causes the problem?
     
    It just happened to me too. New 2405FPW running for 3 days with an NVidia FX5950 Ultra.
    I connect both DVI (with dual link cable) and VGA (through a KVM switch). Both at 1920x1200.
     
    There was some rapid fluctuation of power while I was working on the PC (I have the PC and the monitor on a UPS) and the screen went blank. Both screen and computer were still powered up.
    VGA and DVI had no signal and pressing the auto-configure button was giving a message that the computer was in power-save mode and I should reboot it.
    I did that since nothing else worked, and everything was back to normal.
     
    I never had that before with my previous CRT monitors. The only difference, and the reason for suspecting Windows, is that I set the monitor's power-save mode to activate after 15 minutes of inactivity. Might be Windows thought it was a ghost typing on the keyboard.
     
    Anyway, I disabled power-save and will see what happens.
     
  • khammo01

    27 Posts

    374

    0

    Posted March 13th, 2006 03:00

    Were your previous CRT monitors also DVI connected? FWIW, DVI is using a totally different video signal protocol and that is why we are seeing problems here. When running at 1900x1200 we are so close to the maximum specified data rate that we could be having problems with data corruption.