UNSOLVED

khenryQ

updated

1 month ago

K

khenryQ

1 Rookie

•

2 Posts

0

1485

November 20th, 2025 17:10

14 Premium PA14250, fan noise as they cycle on and off repeatedly

We have about 20 PA14250 so far and we've got reports (and observed on my test system) that the fans make a buzz or whir noise repeatedly. 

It looks like at low load the fans stop completely, then will turn on to a somewhat high speed and slowly ramp back down. There is a support KB doc indicating a noise problem on BIOS lower than 2.0.2 but ours are all well beyond that version and a noise persists. I don't think we ever received any with a BIOS below 2.0.2 so maybe the noise was worse or different before. 

https://www.dell.com/support/kbdoc/000291496/fan-noise-on-dell-pro-13-premium-pa13250-and-dell-pro-14-premium-pa14250?lang=en

Does anyone have experience with this on their systems? I'd like to replace the fans but not sure if that will make a difference, it sounds more like a problem with the control circuit using a bad motor control profile which would remain after fan replacement. If I remove the fans the noise goes away but obviously that isn't useful outside of testing and isolating the problem. 

Appreciate the community's insights here. 

(edited)

  • Margie129Palmer

    1 Rookie

    •

    1 Message

    •

    2 Points

    3

    0

    Posted November 21st, 2025 06:19

    Hello!

    The fan buzz on PA14250 systems isn’t a hardware fault but comes from the control logic: at low load the fans stop, then spin up quickly and ramp down, creating noise. Replacing fans won’t help—only a firmware update or adjusting power/thermal settings to reduce stop‑start cycles can mitigate it. 

  • khenryQ

    1 Rookie

    •

    2 Posts

    4

    0

    Posted November 21st, 2025 15:20

    I suspected as much. I'm really puzzled why the fans don't start on a slow speed. Brushless motors like all small computer fans can be started at low torque. I think the noise is from a high power setting at the initial turn-on and then it ramps down to a reasonable speed, but then shuts off entirely. (I used to work for a motor control company)

    This is frankly a defective fan control profile that is more what I would expect from a cheap laptop that doesn't use PWM, not a Pro Premium anything. The firmware should be updated to modulate to a steady speed when possible and otherwise have a shallower ramp up at initial turn on. Our CEO and CFO really are not impressed with this model after 'upgrading' from their Latitude 7440 :( 

    Adjusting the power\thermal settings will have a pretty significant impact on power consumption either shorter battery run time or lower performance - I should be able to tell our employees to use Optimized in Dell Optimizer as we have done for years.

  • tl06

    1 Rookie

    •

    1 Message

    •

    5 Points

    1

    0

    Posted October 15th, 2026 19:03

    Hi all,

    I have the exact same behaviour on a Dell Pro 14 Essential PV14250 (Core 7 150U, BIOS 1.8.0, Intel DTT 9.1.10010.2297, Windows 11). The fan stops completely at light load, then restarts abruptly at a fairly high speed, slows down, stops again, and repeats. It happens in every Dell Optimizer thermal mode, including Quiet. ePSA passes with no errors, and Dell support's first suggestion was a hardware intervention.

    I logged fan speed, temperatures, CPU power and load every second to understand what is going on. Here is what I found, in case it helps others and Dell:

    • The cycle is driven by temperature, not by any process. The fan starts when the CPU temperature reported by the embedded controller (EC) reaches about 57–60 °C, and stops at about 47–52 °C. While it is off, the CPU only draws 5–8 W at 13–17 % load: plain office use. That heat alone is enough to reach the threshold again within 1–2 minutes, so the cycle repeats 15–30 times per hour depending on the mode.
    • The fan never runs below ~3,200 rpm in automatic mode. Observed speeds were 0, ~3,200, ~4,200 and ~5,500 rpm (the last one in Cool mode). Quiet mode only makes the off periods longer; the restart speed is the same.
    • The BIOS fan table has a 2,600 rpm level that automatic mode never uses. The nominal speeds per level are 0 / 2,600 / 3,800 / 6,000 rpm.
    • The fan and the cooling can handle that level. In a short controlled test, the fan held 2,600 rpm steadily. Under a sustained load of about 10 W (≈57 % CPU), the CPU temperature leveled off at 59 °C, with no power or thermal limiting.

    So, like the original poster, I'm convinced this is a firmware / Intel DTT fan-policy issue. A low running speed of about 2,600 rpm, used before jumping to ~3,200 rpm or stopping, would remove most of the noise. Replacing the fan would not change the policy.

    I have opened a ticket with Dell support and sent a full technical report. I'll post here if I get a BIOS or DTT update that changes the behaviour.

    @Dell staff: several models of the 2025 Dell Pro line seem affected (PA14250 here, PV14250 on my side). Could this be escalated to the BIOS / thermal engineering team?

    To others affected: it would help to reply with your exact model, BIOS version and whether ePSA passed. That makes it easier for Dell to see that this is not an isolated case.