UNSOLVED

Ican1v5

updated

3 months ago

I

Ican1v5

1 Rookie

•

20 Posts

0

1821

May 14th, 2022 21:00

Aurora R14, swapping fans and errors

I bought 3 be quiet fans and swapped out my stock fans from alienware to use on my old pc.

Sometimes if I boot up my pc, fan #2 would fail and if i restart right there, it will be working fine.

I've returned and gotten another fan but the same happens.

Then I tried to swap the fan around. Every time it would be fan #2.

If I put stock fan back, everything would be fine.

Any geniuses here can figure out why this happens?

  • F34R

    2 Intern

    •

    436 Posts

    1145

    2

    Posted May 14th, 2022 22:00

    I believe it's because the fans are starting at a lower RPM than what the BIOS is looking for.  Also, why on Earth would someone want to use stock AW fans on any computer?  yikes.

    Go into AWCC and adjust the fans to have a +10% offset.  Keep increasing that until you don't get the error any more.

  • DELL-Chris M

    Community Manager

    •

    56891 Posts

    •

    232143 Points

    1121

    0

    Posted May 15th, 2022 06:00

    Your post is confusing. Clarify.

    "I bought 3 be quiet fans and swapped out my stock fans from alienware to use on my old pc."
    Meaning = "I bought 3 be quiet fans and swapped out my stock fans from Alienware (Aurora R14?) to use on my old pc (model?)."

    "Sometimes if I boot up my pc,"
    Which one? The Alienware or old PC?


    DELL-Chris M (old account)

    #IWork4Dell

  • Ican1v5

    1 Rookie

    •

    20 Posts

    1094

    0

    Posted May 15th, 2022 17:00

    I tried that. But it's louder than the quiet profile. quiet can go as low as 11% but if i set it to 10% offset itll be above 22%.

    First load after I went shopping no failure though. I will set it to 10% offset every time before I shut down for now and observe behavior.

    Thanks for your help.

  • Ican1v5

    1 Rookie

    •

    20 Posts

    1094

    0

    Posted May 15th, 2022 18:00

    my new r14

  • Vanadiel

    8 Professor

    •

    7094 Posts

    •

    29695 Points

    1074

    0

    Posted May 16th, 2022 03:00

    Support for aftermarket fans is limited on these systems. That is why you get fan errors during post.

  • Saintjorge304

    1 Rookie

    •

    4 Posts

    802

    1

    Posted October 10th, 2022 22:00

    I literally just got this error message on my R14. I put in all nocturnals. Please let me know if you figured out a solution. Thanks. 

  • Vanadiel

    8 Professor

    •

    7094 Posts

    •

    29695 Points

    789

    0

    Posted October 11th, 2022 04:00

    There are only going to be certain Noctua fan models that work.

  • Cb129

    1 Rookie

    •

    7 Posts

    •

    23 Points

    0

    0

    Posted August 10th, 2026 13:06

    I know this post is old, but, I had a similar issue with the fans on my R14 Ryzen Edition after upgrading the GPU and PSU. Mine came with only two case fans, a front intake and rear exhaust, not including the CPU fan. The stock fans are actually server style fans that can reach nearly 5,000 RPM. Because my new GPU was significantly larger than the stock GPU, it restricted more airflow. So I added a second front intake fan and a top exhaust fan. AWCC recognized the new fans but they could only reach around 2,000 RPM. I kept getting errors saying System Fans 3 and 4 had failed.

    The problem was that the R14's system is designed to detect fan speeds similar to the high RPM stock fans. Since the new fans couldn't get anywhere near those speeds, the system interpreted them as failed fans. I eventually replaced those two new fans with a new set of 4 pin PWM fans that had maximum RPM ratings much closer to the stock fans. I also adjusted the fan offset percentages in AWCC so the new fans minimum speeds closely matched what the system expected from the stock fans. After doing that the fan errors stopped completely and everything has worked perfectly since.